background image

A

 Z-Wave devices control other Z-Wave devices. The relationship between one device controlling 

another device is called association. In order to control a different device, the controlling device needs to 

maintain a list of devices that will receive controlling commands. These lists are called  association groups 

and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event 

happens all devices stored in the respective association group will receive a common wireless command.

Association Groups:

1

Devices to be switched on upon motion deteced and off after a timeout (on time) (max. nodes in 

group: 5)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can 

adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128 

… 255 the value sent in the application shall be the desired value minus 256. For example: to set a 

parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value 

the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Sensor report type on Get without instances (Parameter Number 1, Parameter Size 1) Which type of multi 

sensor report should be sent on multi sensor Get command without instances

Value

Description

0

Temperature, humidity and luminance (Default)

1

Temperature

2

Luminance

3

Humidity

Wake up 10 minutes when batteries are inserted (Parameter Number 2, Parameter Size 1) Stay awake for 

10 minutes after batteries are inserted

Value Description

0

No (Default)

1

Yes

On time (Parameter Number 3, Parameter Size 2) How long should the device associated to multi senor 

keep state On before sending it Off command (if the value is bigger than 255, the value would be rounded to 

next integer in minutes)

(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 5 

Содержание AEO MULTISENS









Отзывы: