AEM 30-0311 Скачать руководство пользователя

Страница: 1 / 9

P/N 30-0311

X-SERIES GAUGE

OBD-II

STOP! - READ THIS BEFORE INSTALL OR USE!

WARNING:
THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM. DAMAGE
TO SENSITIVE ELECTRONICS, FIRE, OR EXPLOSION MAY OCCUR IF PROPER PRECAUTION IS NOT TAKEN. IF THERE
IS ANY DOUBT,

DO NOT

ATTEMPT THE INSTALLATION AND CONSULT A PROFESSIONAL.

NOTE

: IT IS THE RESPONSIBILITY OF THE ENGINE TUNER TO ULTIMATELY CONFIRM THE CALIBRATION USE FOR

ANY PARTICULAR ENGINE IS SAFE FOR ITS INTENDED USE. AEM HOLDS NO RESPONSIBILITY FOR ANY ENGINE
DAMAGE THAT RESULTS FROM THE MISUSE OF THIS PRODUCT.

Instruction

Manual

Features

2-1/16" / 52mm outer diameter mounting

Only model year 2008 and newer vehicles (CAN bus
based OBD) supported

41 OBD-II parameters (PIDs) supported

Read and clear Diagnostic Trouble Codes (DTCs)

US or Metric / SI display modes

Black bezel / faceplate supplied; Silver/white available
as optional purchase

Locking connectors

Auto-dimming

Supports vehicle/system voltages up to 16V

KIT CONTENTS

Description

10-0311

INST, X-SERIES OBD2 GAUGE

35-0311

GAUGE ASSY, X-SERIES OBD2 GAUGE

35-8618

NUT, KNURLED, M4x0.7 (2)

35-8614

BRACKET, X-SERIES GAUGE

35-8617

RUBBER BAND, X-SERIES GAUGE

35-3458

CABLE, X-SERIES GAUGE PWR/IO OBD2 V2

*OPTIONAL* ACCESSORIES

Description

30-0311-

ACC

BEZEL, X-SERIES SILVER

FACEPLATE, X-SERIES OBD2, WHITE

Содержание 30-0311










Результаты поиска

Содержание 30-0311

Отзывы:

Похожие инструкции для 30-0311

Бренды по названию

Популярные бренды

AEM 30-0311, Инструкция по эксплуатации

Результаты поиска

Содержание 30-0311

Отзывы:

Похожие инструкции для 30-0311

Бренды по названию

Популярные бренды