background image

11

English

mAINTENANCE

NOTE:

  Used  oil  should  be  disposed  of  at  an  approved 

disposal site. See your local oil retailer for more information.

CLEANING FUEL SEDIMENT CUP

The sediment cup prevents dirt and water that may have gotten 

into the fuel tank from entering the carburetor. If the engine 

has not been run for a long time, the sediment cup should be 

cleaned before use.

n

 

Turn the fuel valve to the OFF position.

n

 

Remove the sediment cup using a 10 mm wrench (not 

provided).

n

 

Remove the O-ring and filter.

n

 

Clean  each  of  the  parts  in  carburetor  cleaner  or  any 

comparable cleaning product.

n

 

Reinstall  the  filter,  O-ring,  and  sediment  cup.  Tighten 

with wrench to secure.

n

 

Return the fuel valve to ON position and check for leaks.

CLEANING THE EXHAUST PORT AND MUFFLER

Depending on the type of fuel used, the type and amount of 

oil used, and/or your operating conditions, the exhaust port 

and  muffler  may  become  blocked  with  carbon  deposits.  If 

you notice a power loss with your petrol-powered tool, you 

may need to remove these deposits to restore performance. 

We highly recommend that only qualified service technicians 

perform this service.

DRAINING FUEL TANK

When not using a fuel stabiliser, draining the fuel from the 

tank before storage may help prevent gum deposits in the 

fuel system.

n

 

Turn the engine switch OFF ( O ).

n

 

Close fuel valve.

n

 

Remove the fuel line from the petcock by squeezing the 

ends of the retaining clip and sliding the fuel line off.

n

 

Install  one  end  of  a  drain  line  over  the  petcock,  and 

place the other end in a fuel container large enough to 

catch the fuel being drained from the tank.

n

 

Open fuel valve.

n

 

When the fuel has drained from the tank, close the fuel 

valve and reinstall fuel line on petcock.

TRANSPORTING

n

 

Turn engine switch OFF ( O ).

n

 

Close the fuel valve.

n

 

Make sure engine and exhaust of unit is cool.

n

 

Keep unit level to prevent fuel spillage. 

n

 

Do not drop or strike unit or place under heavy objects.

Содержание Powertools AGN5000DEB























Отзывы: