AEG L7FE7261BI Скачать руководство пользователя страница 21

Страница: 21 / 48

The intermediate and the final

spinning phases are suppressed and

the programme ends with water in the

drum. This helps to reduce creasing.

The door stays locked. The drum

turns regularly to reduce creasing.

You must drain the water to unlock

the door.

As the programme is very quiet, it is

suitable for use at night time when

cheaper electricity tariffs are available.

In some programmes the rinses are

performed with more water.

If you touch the Start/Pause button,

the appliance performs only the

draining phase.

The appliance empties the

water out automatically after

approximately 18 hours.

7.6

Prewash

With this option you can add a prewash

phase to a washing programme.
The corresponding indicator above the

touch button illuminates.
• Use this option to add a pre-wash

phase at 30 °C before the washing

phase.

This option is recommended for

heavily soiled laundry, especially if

containing sand, dust, mud and other

solid particles.

The options can increase the

programme duration.

7.7

Permanent Anti-stain

This option adds an anti-stain phase to

the programme. Use this option for

laundry with hard stains to remove.
To

activate/deactivate

this option, hold

the Prewash button pressed for 3
seconds until the indicator

comes on/

goes off

on the display.

Pour the stain remover into compartment

This option increases the

programme duration.

This option is not available

with a temperature lower

than 40 °C.

7.8

Permanent Soft Plus

Set this option to optimise the fabric

softener distribution and improve fabric

softness.
Recommended when you use fabric

softener.

This option increases the

programme duration.

The corresponding indicator above the

touch button illuminates and also stays

permanently on during next cycles until

this option is deactivated.

7.9

Permanent Extra Rinse

With this option you can permanently

have an extra rinse when you set a new

programme.
To

activate/deactivate

this option, hold

the Soft Plus button pressed for 3
seconds until the indicator

comes on/

goes off

on the display.

When it is activated, the appliance will

default to this option after you switch it

off or change/reset the programme.

This option increases the

programme duration.

7.10

Plus Steam

This option adds a steam phase followed

by a short anti-crease phase at the end

of the washing programme.
The steam phase reduces fabric creasing

and facilitates the fabric ironing.
The corresponding indicator above the

touch button illuminates.

The indicator

is steady on during

steam phase.

This option can increase the

programme duration.

ENGLISH

Содержание L7FE7261BI

















































Результаты поиска

Содержание L7FE7261BI

Отзывы:

Бренды по названию

Популярные бренды

AEG L7FE7261BI, Руководство пользователя

Результаты поиска

Содержание L7FE7261BI

Отзывы:

Бренды по названию

Популярные бренды