42
English
42
KRC_IM
17.12.15
Rear view
(without illustration)
Mains cable
Wire antenna
Bottom side
(without illustration)
Speaker
Pre-punched battery compartment (cannot be opened with
this device)
Assembly Instructions
CAUTION:
Make sure that the plug is not inserted when assem-
bling the device!
• Remove all objects from the cupboard and anything
which is fragile in the adjacent cupboards.
• For the installation the cupboard must fulfil the following
conditions:
Thickness of the cupboard floor between
16 mm and 20 mm.
• The wall mounting of the cupboard must be stable and
anchored firmly in the wall with at least 2 screws.
•
Important! Do not install the device above a cooker!
• When installing the device it must be ensured that there is
a power socket within reach.
• The mains socket must be within easy reach, so that the
plug can be quickly removed in an emergency.
•
Important! Do not connect the device to the mains
power supply until after installation!
• The device cannot be installed under cupboards under
which there is a lighting strip.
• For mounting, you may need the following supplies: A
drill with 6 mm drill bit, pilot drill or nail, screwdriver, tape
measure, adhesive tape, scissors, safety goggles.
Supplied mounting accessories
4 Screws
4 Spacers
1 Drilling template
CAUTION:
• Please adhere to the dimensions stated in the installa-
tion instructions.
• You should use only the installation accessories
supplied.
Installation
1. Tape the template firmly down to the shelf with adhesive
tape. With the help of a gimlet or nail pierce the crosses
at the attachment points and use it to mark the holes.
2. Remove the template and drill the holes into the wall
cupboard.
3. Insert the spacer into the holes provided on the device.
CAUTION:
Sufficient ventilation is only guaranteed with a spacer.
4. Countersink the screws into the holes in the cupboard.
5. Using the 4 screws and the spacers, attach the kitchen
radio to the bottom of the cupboard.
6. Tighten the screws finger tight with a screwdriver.
CAUTION:
Use a screwdriver and not a cordless screwdriver.
Installation
• Make sure there is proper ventilation for the device!
• Sensitive surfaces such as the display may be protected
by plastic foil. Remove this foil.
Power Supply
• Ensure that the voltage is the same as that indicated on
the model identification plate.
• Insert the grid plug into a properly installed three prong
socket.
NOTE:
• If the unit is not used for a long period of time, unplug
the mains plug from the socket.
• If the power supply gets disconnected, the time/date
settings will be lost.
First use
1. Unwind the cable antenna completely. Position it vertical-
ly for initial installation.
2. Use button to turn on the device.
3. Select the DAB mode using the MODE button. The
device automatically searches for DAB stations.
SUCHLAUF… and a progress bar appears on the display.
The figure on the right of the display shows the number
of radio stations found. The first alphanumeric DAB
station is played.
When playing a radio station, the time and date is taken
from the broadcasting service. If the device does not
receive DAB stations in your location, set the time manu-
ally as described in “Settings menu”.
Changing the OSD language
The factory default of the OSD menu is German. To change
the language, proceed as follows:
1. Keep the INFO / MENU button (12) pressed for approx.
2 seconds.
2. Select the menu option “SYSTEM” with the SKIP + / SKIP –
buttons (5 / 6). Set it with the SCAN / SELECT button (4).
3. Select the menu option “SPRACHE” with the SKIP + /
SKIP – buttons. Set it with the SCAN / SELECT button.
Содержание KRC 4368 DAB+
Страница 68: ......
Страница 69: ......
Страница 70: ...KRC 4368 DAB Stand 12 2015 KRC4368DAB _IM 17 12 15 Elektro technische Vertriebsges mbH www etv de ...
