English
35
• For the installation the cupboard must fulfil the following
conditions:
Thickness of the cupboard floor
between 16 mm and 20 mm.
• The wall mounting of the cupboard must be stable and
anchored firmly in the wall with at least 2 screws.
•
Important! Do not install the device above a cooker!
• When installing the device it must be ensured that there
is a power socket within reach.
• The mains socket must be within easy reach, so that the
plug can be quickly removed in an emergency.
•
Important! Do not connect the device to the mains
power supply until after installation!
• The device cannot be installed under cupboards under
which there is a lighting strip.
• For mounting, you may need the following supplies: A
drill with 6 mm drill bit, pilot drill or nail, Allen key, tape
measure, adhesive tape, scissors, safety goggles.
Supplied Mounting Accessories
4 Screws
4 Spacers
1 Drilling template
CAUTION:
• Please adhere to the dimensions stated in the installa-
tion instructions.
• You should use only the installation accessories sup-
plied.
Installation
1. Tape the template firmly down to the shelf with adhesive
tape. With the help of a gimlet or nail pierce the crosses
at the attachment points and use it to mark the holes.
2. Remove the template and drill the holes into the wall
cupboard.
3. Insert the spacer into the holes provided on the device.
NOTE:
Sufficient ventilation is only guaranteed with a spacer.
4. Countersink the screws into the holes in the cupboard.
5. Using the 4 screws and the spacers, attach the kitchen
radio to the bottom of the cupboard.
6. Tighten the screws hand-tight with an Allen wrench.
CAUTION:
Use an Allen wrench and not an electric screwdriver.
Start-Up of the Device / Introduction
• Make sure that the device is adequately ventilated!
• If applicable, remove the protective film from the display.
Power Supply
Please ensure that the mains voltage corresponds to the
information on the type plate. Plug the power plug into a
properly installed socket.
Inserting the Power Reserve Battery
(Battery not included in scope of delivery)
During a power outage, or when the power plug is pulled
from the socket, the clock time and the alarm times will be
lost. To prevent this, insert a power reserve battery as follows.
1. Open the battery compartment on the bottom. Turn the
battery compartment lid in the direction “OPEN”.
2. Insert a button cell battery of the type CR 2025 3 V. Ensure
the correct polarity (see battery compartment lid)!
3. Close the battery compartment again.
WARNING:
The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
Danger of explosion!
CAUTION:
• Batteries may leak out and lose battery acid. If the
device is not used for a longer period of time, remove
the battery.
• Batteries do not belong in the household waste.
Dispose of spent batteries at the designated collection
points or at the dealer.
Switching the Device on/off (10)
• Turn on the device by pressing the /FUNC button.
• To turn off the device, keep the /FUNC button pressed
for about 3 seconds.
NOTE:
After about 20 minutes without signal, or if the signal is too
low, the device will switch to Standby automatically.
Selecting the Operating Mode (10)
When the device is turned off, you can switch between
radio and Bluetooth mode by pressing the /FUNC. button
repeatedly.
Setting of the Clock (24 h)
1. Hold down the TIME SET/COOK TIMER button (14) for
approx. 3 seconds. The notification “24H” will appear in
the display.
2. Select the time format with the SKIP+/SKIP- buttons (7/8).
NOTE:
“PM” will show in the display in the afternoon with the
12-hour indication.
3. Press the TIME SET/COOK TIMER button to confirm.
The hour setting will blink in the display.
4. Adjust the setting with the SKIP+/SKIP- buttons (7/8).
