AEG Favorit 65080 Vi Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 40

AEG Favorit 65080 Vi Скачать руководство пользователя страница 32

Installation and connection instructions

32

Installation and connection instructions

1

Safety Information for the Installation

•

Only transport the dishwasher in an upright position, otherwise salt water
may run out.

•

Before using the dishwasher for the first time, check for any damage caused in
transport. Do not under any circumstances connect an appliance that is dam
aged. In the case of damage, please contact your supplier.

•

Never use the dishwasher if the mains cable, water inlet or drain hose are
damaged; or if the control panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.

•

Always plug the mains plug into a correctly installed shockproof socket.

•

Prior to using the appliance for the first time, ensure that the rated voltage
and type of supply on the rating plate match that of the supply where the ap
pliance is to be installed. The fuse rating is also to be found on the rating plate.

•

Multiway plugs / connectors and extension cables must not be used. This
could constitute a fire hazard through overheating.

•

The dishwasher’s cable must only be replaced by a Service Force Engineer.

•

A water inlet hose with safety valve must only be replaced by a Service Force
Engineer.

Installing the Dishwasher

•

The dishwasher must be installed on a firm floor and adjusted to ensure that it
is stable and level in all directions.

•

To compensate for unevenness in the floor and to match the height of the ap
pliance to that of surrounding units, extend the threaded feet using a screw
driver.

•

Adjust the rear foot of the appliance using a cordless screwdriver from the
front of the appliance (see installation template).

•

The drain hose, inlet hose and mains cable must be laid so that they are able to
move freely within the plinth area, and so that they are not kinked or crushed
when the dishwasher is in position.

•

The dishwasher must also be screwed tightly to the work surface or to the ad
joining units. This is essential to ensure the dishwasher does not tip up.

«
...
30
31
32
33
34
...
»

Содержание Favorit 65080 Vi









































Отзывы:

Нет отзывов