manualshive.com logo in svg

AEG BP300302, Руководство пользователя

Поделиться
Скачать
AEG BP300302 Скачать руководство пользователя страница 117

 115

Alpha V8

V. Claim shall be made under this warranty by delivering the Prod-

uct for inspection to a MerCruiser dealer authorized to service
the Purchaser’s product. If purchaser cannot deliver Product to
such authorized dealer, he may give notice in writing to the
Company. We shall then arrange for the inspection and repair,
provided such service is covered under this warranty. Purchas-
er shall pay for all related transportation charges and/or travel
time. If the service is not covered by this warranty purchaser
shall pay for all related labor and material and any other ex-
penses associated with that service. Any Product or parts
shipped by purchaser for inspection or repair must be shipped
with transportation charges prepaid. The Warranty Registration
Card is the only valid registration identification and must be
presented at the time warranty service is required. Warranty
claims will not be accepted without presentation of the Warranty
Registration Card.

VI. Our obligation under this Warranty shall be limited to repairing

a defective part, or at our option, refunding the purchase price
or replacing such part or parts as shall be necessary to remedy
any malfunction resulting from defects in material or workman-
ship as covered by this Warranty. We reserve the right to im-
prove the design of any Product without assuming any obliga-
tion to modify any Product previously manufactured.

VII. ALL INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM THIS WARRANTY. WARRANTIES
OF MERCHANTABILITY AND FITNESS ARE EXCLUDED
FROM THIS WARRANTY. IMPLIED WARRANTIES ARE LIM-
ITED TO THE LIFE OF THIS WARRANTY. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO
YOU.

VIII. This warranty gives you specific legal rights, and you may also

have other legal rights which vary from state to state.

Содержание BP300302









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды