11
11
MAINTENANCE
WARNING
For greater safety and reliability, all repairs should be performed by
an authorised AEG service centre.
Avoid using solvents when cleaning plastic parts. Most plastics are
susceptible to damage from various types of commercial solvents and
can be damaged by their use. Use clean cloths to remove dirt, dust,
oil, grease, etc.
Do not modify the product in any way or use accessories not
approved by the manufacturer. Your safety and that of others may
be compromised.
Before and after each use, check the product for damage or broken
parts. Keep the product in top working condition by immediately
replacing parts with spares approved by the manufacturer.
When servicing, use only identical replacement parts. Use of any other
parts may create a hazard or cause product damage.
Use only AEG accessories and AEG spare parts. Should components
need to be replaced which have not been described, please contact
one of our AEG service agents (see our list of guarantee/service
addresses).
REPLACING THE CLAMP PADS
See Figure 21.
To replace clamp pads or to remove them for greater clamping range:
To replace the clamp pad on the fixed clamp:
Ŷ
Pry off the fixed clamp pad using a flathead screwdriver.
Ŷ
Place a new clamp pad over the holes in the fixed clamp and press
the pad into place.
To replace the clamp pads on the sliding clamp:
Ŷ
Remove the front and back clamp pads.
Ŷ
Place a new front clamp pad into the holes on the sliding clamp.
NOTE
: Front clamp pad must be installed before the back clamp
pad.
Ŷ
Align the new back clamp pad holes over the tabs from the front
clamp pad and press the pads together.
LUBRICATING THE CLAMP MECHANISM
See Figure 22.
If the sliding clamp does not move smoothly, remove it and spray the
clamp mechanism with a small amount of general purpose grease.
ADJUSTING THE LOCK LEVERS
See Figure 23 - 24.
In the “locked” position, the action of pushing the leg lock lever or foot
lock lever down should feel tight and secure. If the levers are loose or
too tight, an adjustment may be required.
To adjust the leg lock lever:
Ŷ
Fold the product.
Ŷ
Unlock the leg lock lever.
Ŷ
Rotate the leg lock lever clockwise to tighten and counterclockwise
to loosen.
To adjust the foot lock lever:
Ŷ
Fold the product.
Ŷ
Unlock the leg lock lever.
Ŷ
Slide the rear leg to the back of the product releasing it from the
storage position.
Ŷ
Lift the leg slightly then slide the leg toward the front of the
product.
Ŷ
Raise the leg and slide it down into place before locking the leg
lock lever.
Ŷ
Unlock the foot lock lever.
Ŷ
Use a wrench to hold the nut in place.
Ŷ
Rotate the foot lock lever clockwise to tighten and
counterclockwise to loosen.
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
Techtronic Industries Australia Pty Ltd
PO Box 1065
Mount Waverley VIC 3149
Tel. no. 1300 234 797
Australia
Techtronic Industries N.Z. Limited
PO Box 12-806
Penrose AUCKLAND 1642
Tel no. 0800 234 797
New Zealand
SYMBOLS
Safety alert
Please read the instructions carefully before
starting the product.
Do not reach into the gap. Beware of pinching.
Wear eye protection.
250
Do not exceed 250 kg.
Do not stand on top or use as ladder.
Do not sit on top.
Содержание ASJ-01
Страница 1: ...ASJ 01 Original instructions ...
