AEG ACS183060, Оригинальное руководство пользователя

Страница: 31 / 36

31
31
WARNING! Remove the battery before adjustment,
maintenance or cleaning. Failure to do so could result in
serious personal injury.
You may only make adjustments or repairs described in this manual.
For other repairs, contact the authorised service agent.
Consequences of improper maintenance may cause the chain brake
and other safety features to not function correctly, thus increasing
the potential for serious injury. Keep your chainsaw professionally
maintained and safe.
Sharpening the chain safely is a skilled task. Therefore, the
manufacturer strongly recommends that a worn or dull chain
is replaced with a new one, available at your authorised service
centre. The part number is available in the product specification
table in this manual.
Follow instructions for lubricating and chain tension checking and
adjustment.
After each use, clean the product with a soft dry cloth.
Check all nuts, bolts, and screws at frequent intervals for security
to ensure the product is in safe working condition. Any part that is
damaged should be properly repaired or replaced by an authorised
service centre.
Replacing the guide bar and saw chain
See pages 16 - 18.
Make sure to remove the battery pack from the product. Wear
protective gloves.
Remove the bar mounting nuts using the combination wrench
provided.
Remove the chain cover.
Remove the bar and saw chain from the product.
Put the new chain in the correct direction onto the bar and make
sure that the drive links are aligned in the bar groove.
Attach the bar to the chain saw and loop the chain around the drive
sprocket.
Replace the chain cover and bar mounting nuts.
Finger-tighten the bar mounting nuts. The bar must be free to move
for chain tension adjustment.
Adjust the chain tension. Refer to the “Adjusting chain tension”
section.
Hold the tip of the guide bar up and tighten the bar mounting nuts
securely.
WARNING! A dull or improperly sharpened chain can
cause excessive motor speed during cutting which may result
in severe motor damage.
WARNING! Improper chain sharpening increases the
potential of kickback.
WARNING! Failure to replace or repair a damaged chain
can cause serious injury.
WARNING! The saw chain is sharp. Always wear protective
gloves when performing maintenance to the chain.
Inspecting and cleaning the chain brake
Always keep the chain brake mechanism clean by lightly brushing
the linkage free from dirt.
Always test the chain brake performance after cleaning. Refer to
“Checking and operating the chain brake” section in this manual for
additional information.
MAINTENANCE SCHEDULE
Daily check
Bar lubrication Before each use
Chain tension Before each use and
frequently
Chain sharpness Before each use, visual
check
For damaged parts Before each use
For loose fasteners Before each use
Chain brake function Before each use
Inspect and clean
Bar Before each use
Complete saw After each use
Chain brake Every 5 hours of operation
Spare parts Oregon
Chain 90PX045X
Bar 124MLEA041
Exploded view
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364
Winnenden, Germany.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture.
Store the battery packs in a 30% - 50% charged condition.
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
■ The user can transport the batteries by road without further
requirements.
■ Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
■ Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
■ Ensure that battery pack is secured against movement within
packaging.
■ Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
SYMBOLS
Safety alert
Read and understand all instructions before
operating the product, follow all warnings and
safety instructions.
Wear eye, ear and head protection.
Wear non-slip safety footwear when using the
product.
Wear non-slip, heavy duty gloves.
Wear eye and face protection.
Wear upper body protection.
Wear leg protection.
Beware of chain saw kickback and avoid contact
with bar tip.
Do not expose to rain or damp condition.
Moving direction of the chain.
(Marked under the chain cover)
Hold and operate the saw properly with both
hands.
Do not operate the saw using only one hand.
Remove the battery pack before starting any work
on the product.
Do not burn used battery packs.
Never charge a damaged battery pack. Replace
with a new one.