AE Techron 7212 Скачать руководство пользователя страница 33

Страница: 33 / 49

97-7224006_3-31-15

Information subject to change

7224 OPERATOR’S MANUAL – SECTION 5

The SIM-BNC-OPTOC module is required for all
Series configurations and should be used in con

junction with the DB9M CABLE (see below).

DB9M CABLE

– The DB9M (OPTOC) CABLE is a

high-voltage Interlock cable that provides superior
insulation for multi-amp series systems running
high-voltage applications.

The DB9M CABLE is required for all Series con

figurations and should be used in conjunction with
the SIM-BNC-OPTOC module (see above)

BAL RES KIT

– Three types available: 7224 BAL

RES KIT, 7548 BAL RES KIT and 7796 BAL RES
KIT. Ballast resistors are required for all Parallel
configurations. The ballast resistor kits include one
ballast resistor (two in the 7796 kit) with connec

tion terminals and mounting hardware. The 7224

BAL RES KIT also contains the shunt required to
defeat the amplifier’s external level control.

PARALLEL WIRING KITS

– Six types available:

7224 2-AMP, 7548/7796 2-AMP, 7224 3-AMP,
7548/7796 3-AMP, 7224 4-AMP, and 7548/7796
4-AMP. Parallel wiring kits include the DB-25 Inter

lock cable for system communication, BNC T-con-
nectors and BNC patch cables for wiring parallel
inputs through the BNC input connectors, and the

output wiring for connecting system amplifiers to
the load. The kits also include the wire(s) needed

for wiring the parallel inputs through the Remov-

able Barrier Block (WECO) connectors and the

.input terminators required during system setup.
Parallel wiring kits are recommended for all Paral-

lel configurations.

To download the AE Techron

7000-Series Multi-

Amp Configuration Guide

or for additional

information, visit the AE Techron website at

www.

aetechron.com.

5.3.1 Accessory Recommendations by

System Type

Series Systems

7224 Two in Series:

(2) SIM-BNC-OPTOC input cards,

(1) DB9M OPTOC cable

7224 Three in Series:

(3) SIM-BNC-OPTOC input cards,

(2) DB9M OPTOC cables

Parallel Systems

7224 Two in Parallel:

(2) 7224 BAL RES kits,

(1) 7224 2-AMP Parallel Wiring kit

7224 Three in Parallel:

(3) 7224 BAL RES kits,

(1) 7224 3-AMP Parallel Wiring kit

7224 Four in Parallel:

(4) 7224 BAL RES kits,

(1) 7224 4-AMP Parallel Wiring kit

Содержание 7212


















































Результаты поиска

Содержание 7212

Отзывы:

Похожие инструкции для 7212

Бренды по названию

Популярные бренды

AE Techron 7212, Руководство оператора

Результаты поиска

Содержание 7212

Отзывы:

Похожие инструкции для 7212

Бренды по названию

Популярные бренды