AE Techron 7212 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

background image

97-7224006_3-31-15

Information subject to change

21

7224 OPERATOR’S MANUAL – SECTION 4

Figure 4.8 – Standby Mode on Over Temp Setting

Figure 4.9 – Standby Mode on Over Load Setting

4.2.6 Standby Mode on

Over Temp Setting

When enabled, the 7224 amplifier will move into

Standby mode when it senses any activation of

the Over Temperature circuit. The amplifier will
remain in Standby mode until the amplifier is reset.
To reset the amplifier, push and hold the Reset
switch on the amplifier front panel until the Stand

-

by LED goes out, then release the Reset switch.

Alternately, the amplifier will reset when a Reset
signal is received on the Interlock – I/O Connector.
Once reset, the amplifier will return to Run mode.

To enable S

tandby mode on Over Temp,

place

the jumper across the two pins labeled J12. See

Figure 4.8.

4.2.7 Standby Mode on

Over Load Setting

When enabled, the 7224 amplifier will move into

Standby mode when it senses an activation of the

IOC (Input/Output Comparator) Distortion Alert
circuit. The IOC Distortion Alert circuit continuously

compares the input waveform to the output wave-

form. When a distortion of more than 0.5% occurs,
the IOC circuit will activate. The amplifier will re

-

main in Standby Mode until the Reset switch on the

front panel is pushed or a Reset signal is received

on the Interlock – I/O Connector. Once reset, the
amplifier will return to Run mode. To enable

Stand

-

by mode on Over Load,

place the jumper across

the two pins labeled

J13.

See

Figure 4.9.

4.3

Configuration Settings Located on

the Power Supply Board

The following custom settings can be made via
plug-in connectors located on the Power Supply

Board:

•

Amplifier Voltage Potential setting (high current
or high voltage)

• Bi-Level Power Supply setting

4.3.1 Selecting the Best Voltage

Potential and Bi-Level Power Switch

Settings for Your Application

The output of the amplifier will be determined by

the combination of settings used for both Voltage
Potential and Bi-Level Power Switch.

OUTPUT VOLTAGE

Bi-Level

Switch Setting

Voltage Potential Setting

90

180

Auto

45-90

90-180

High

90

180

Low

45

90

«
...
19
20
21
22
23
...
»

Содержание 7212


















































Отзывы:

Нет отзывов

Похожие инструкции для 7212

Бренд: Zeck Audio Страницы: 6

Бренд: icon Audio Страницы: 9

SINGLE RECTIFIER RECT-O-VERB 50 2 Series

Бренд: Mesa/Boogie Страницы: 11

Бренд: Optimus Страницы: 19

Бренд: Rockford Fosgate Страницы: 12

Бренд: Channel Vision Страницы: 8

Бренд: zapco Страницы: 12

Бренд: Surpass Страницы: 14

Бренд: Rotel Страницы: 146

Бренд: Siegmund Страницы: 10

Бренд: DaytonAudio Страницы: 28

Бренд: Nova Страницы: 16

Бренд: Gradus Group Страницы: 8

Бренд: Kramer Страницы: 33

Бренд: Cloud Страницы: 11

Бренд: PARK AUDIO Страницы: 16

Бренд: Sansui Страницы: 13

Бренд: CyberData Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды