Advida P-25 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

Advida P-25 Скачать руководство пользователя страница 14

14

Precautions for installation

Installation area for this product

Contact your dealer for assistance if you are
unsure of an appropriate place in your particu-
lar environment.

• Make sure that the installation area is

strong enough to hold this product, such
as a concrete ceiling.

• Install the camera in the foundation area of

the architecture or where sufficient strength
is assured.

• If a wall or ceiling board such as plaster

board is too weak to support the total
weight, the area shall be sufficiently rein-
forced.

Do not place this product in the following
places:

• Locations where a chemical agent is used

such as a swimming pool

• Locations subject to oil smoke such as a

kitchen

• Locations that have a specific environment

that is subject to an inflammable atmo-
sphere or solvents

• Locations where a radiation, an X-ray, a

strong radio wave or a strong magnetic
field is generated

• Locations where corrosive gas is pro

-

duced, locations where it may be damaged
by briny air such as seashores

• Locations where the temperature is not

within the specified range (

☞

page 40).

• Locations subject to vibrations, such as on

vehicles, marine vessels, or above product
lines (This product is not designed for on-
vehicle use.)

Check before installation

Compatibility of devices is restricted. Before
installation, check the ratings and dimensions
of the devices to be used.
Contact your dealer for details.

Before installation

• Use the camera mount bracket (accessory)

to install the camera on the ceiling or wall.

• Anchor bolts and screws used to mount

the camera on the ceiling or wall are not
supplied. Prepare bolts and screws that
match the structure and materials of the
installation location and satisfy the
performance and reliability specifications
shown below.

• Required screws:

Directly installed on a wall or ceiling:
M5 screw x4
Secure the camera to a two-gang junction
box:
M4 screw with Spring washer and ø7.5

～

10 Washer x4

Secure the adapter box: M5 screw x4

• Minimum pull-out strength: 539 N {121 lbf}

(per 1 pc.)

Power supply

This product has no power switch.
When turning off the power, turn off a power
supply or remove a power cable. When the
power cable of the product is connected to the
power supply device, the power will be
supplied to the product.
Before cleaning the product, make sure that
the power cable is not connected to the main
power supply.

About the network connection

When connecting to a network using the network
cable of this product, observe the following.

• When wiring for the network, design and

engineer not to be affected by thunder.

• It is impossible to install this product in

combination with a pan/tilt head.

Advidia assumes no responsibility for injuries or property damage resulting from failures
arising out of improper installation or operation inconsistent with this documentation.

«
...
12
13
14
15
16
...
»

Содержание P-25

















































Отзывы:

Нет отзывов