Advantek PixLite R2F-S Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 15

Advantek PixLite R2F-S Скачать руководство пользователя страница 9

- 9 -

www.advateklights.com

PixLite R2F-S User Manual V200702

4 - Operation

4.1 - Start-up

When power is applied to the receiver, the green power led in the bottom right-hand
corner on the front panel should be illuminated, as shown in

below.

Figure 7: Position of the Power LED

If pixels have been correctly connected to the outputs and the data cable is
connected to the transmitter and valid data is being sent, you should see the pixels
turn on.

4.2 - Indicator LEDs

Each fuse is paired with a green LED which indicates the condition of the fuse. If the
fuse is good, the LED will be on. If the fuse has been blown or is not connected, the
LED will be off. This feature offers a quick method for determining the state of each
fuse, however in environments where these LEDs are needed to be turned off, a switch
is located underneath the spare fuse that will turn off this feature. If the switch is
pushed to the right, it is off, and all indicator LEDs and the power LED will always be
off. This switch is shown in

below.

«
...
7
8
9
10
11
...
»

Содержание PixLite R2F-S
















Отзывы:

Нет отзывов