background image

                                                                                 

                                                                                             

Page 13 of 14                                     

Enabling an Intelligent Planet                       

       

www.advantech.com

 

Troubleshooting 

 

No picture   

The signal cable should be fully connected to the graphics card/computer.   
The graphics card should be completely seated in its PC slot.   
Power Button and computer power switch should be in the ON position.   
Check to make sure that a supported mode has been selected on the graphics card 
or system being used. (Please consult graphics card or system manual to change 
graphics mode).   
Check the monitor and your graphics card with respect to compatibility and 
recommended settings.   
Check the signal cable connector for bent or pushed-in pins.   
Check that the BNC

 

or

 

D-SUB button is in the correct position.   

 

Power Button does not respond   

Unplug the power cord of the monitor from the AC outlet to turn off and reset the 
monitor, or simultaneously press the RESET and Power buttons. 
 

Image is unstable, unfocused   

Signal cable should be fully connected to the computer.   
Use the OSM™ Image Adjust controls to focus and adjust display by increasing or 
decreasing the Fine control. When the display mode is changed, the OSM Image 
Adjust settings may need to be re-adjusted.   
Check the monitor and your graphics card with respect to compatibility and 
recommended signal timings. 
 
If your text is garbled, change the video mode to non-interlace and use 60Hz refresh 
rate.   

Содержание ProFlat IDP-31320W
















Отзывы: