Advantech PCL-832 Скачать руководство пользователя

Страница: 46 / 63

PCL-832 User's Manual

MCC_jog_c [MEX10.C]

Function

moves at a specified speed

Syntax

int MCC_jog_c(char x, char d,

int s_ratio)

Parameter

x( x = 1, 2, 3 )

specifies the axis

the movement direction

d = +1

d = -1

CCW

s_ratio

the movement speed ratio (%)

Return value

0 if successful, other value if not

Note:

The motor will keep on moving at the specified speed until
MCC_motion_hold is executed. To abort the movement, call
MCC_motion_abort.

Motion function return codes

The return codes of the motion functions have the following meaning:

Function successful

-1:

The system queue buffer is full. Call the function again

-2:

An error has occurred. Call MCC_get_errcode to get the error
code, and call MCC_clear_error to clear the error flag

-3:

fspd = 0

Utility functions

MCC_motion_hold [MEX11.C]

Function

holds the current machine curve

Syntax

int MCC_motion_hold()

Return value

0 if successful, other value if not

MCC_motion_abort [MEX10.C]

Function

aborts the motion curve that was held

Syntax

int MCC_motion_abort()

Return value

0 if successful, other value if not

Содержание PCL-832
































































Результаты поиска

Содержание PCL-832

Отзывы:

Похожие инструкции для PCL-832

Бренды по названию

Популярные бренды

Advantech PCL-832, Руководство пользователя

Результаты поиска

Содержание PCL-832

Отзывы:

Похожие инструкции для PCL-832

Бренды по названию

Популярные бренды