Advantech ICR-4461 Скачать руководство пользователя

Страница: 37 / 54

ICR-4461

4. Technical Parameters

4.1

Basic Parameters

Parameter

Description

Temperature range

Operating
Storage

-40

◦

C to +75

◦

C (-40

◦

F to +167

◦

-40

◦

C to +85

◦

C (-40

◦

F to +185

◦

Humidity

Operating
Storage

5 to 95 % relative humidity non condensing
5 to 95 % relative humidity non condensing

Altitude

Operating

2000 m / 70 kPa

Degree of protection

IP30

Supply voltage

9 – 48 V DC

Battery for RTC

CR1225

Consumption for
non-WiFi (WiFi)
version

Idle
Average
Maximum

LPM mode

5.6 W (6.5 W)
6.5 W (8.8 W)
10.9 W (14.2 W) / 142 W

3 mW / 170 mW

Dimensions of device (w/o wings)

195

110

47 mm (7.68"

4.33"

1.85")

DIN rail clip specification

2 pcs of DIN 35 mm, EN 60715

Total weight

1275 g (2.81 lbs)

Antenna connectors

ANT1, ANT3
ANT2, ANT4
WIFI1

shared SMA female connectors for 5G/GNSS – 50

Ω

SMA female connectors for 5G – 50

Ω

RP-SMA female connectors for WiFi – 50

Ω

Interfaces

ETH0
ETH1
ETH2
USB
SERIAL & I/O

RJ-45 socket for 1Gb Ethernet SWITCH
RJ-45 socket for 1Gb Ethernet
SFP cage for up to 10 Gbps SFP modules
USB-A
14-pin panel socket terminal block for RS232, RS485,
CAN bus and I/O interfaces

Table 15: Basic Parameters

Maximal power consumption for model with the PoE PSE (for maximal power load on all ETH0 ports).

For device equipped with the PoE PSE.

Содержание ICR-4461























































Результаты поиска

Содержание ICR-4461

Отзывы:

Похожие инструкции для ICR-4461

Бренды по названию

Популярные бренды

Advantech ICR-4461, Руководство пользователя

Результаты поиска

Содержание ICR-4461

Отзывы:

Похожие инструкции для ICR-4461

Бренды по названию

Популярные бренды