Advantech ICR-4461 Скачать руководство пользователя

Страница: 34 / 54

ICR-4461

2.13

Reset Functions

Consider creating a router configuration backup before performing the router’s factory
reset.

The

RST

button can be used in three different scenarios:

•

Reset

: Hold the

RST

button for

less than 4 seconds

; the router will reboot, applying its

customized configuration. The router reset can be initiated by clicking the

Reboot

item in the router web GUI.

•

Factory Reset

: To restore the default factory configuration of the router, press and hold

the

RST

button for

more than 4 seconds

. After that, the

PWR

LED turns off and on

again. We recommend holding the

RST

button for 1 second after turning on the PWR

LED.

•

Emergency Factory Reset

: If the router cannot boot up due to the incorrect configu-

ration, turn off the router (disconnect the power supply). Then, push and hold the

RST

button, turn on the router and hold the

RST

button for

at least 10 seconds

. The router

configuration will be set to the default one.

It is necessary to use a narrow screwdriver or any other small tool to press the

RST

button.

Figure 23: Resetting the Router

Содержание ICR-4461























































Результаты поиска

Содержание ICR-4461

Отзывы:

Похожие инструкции для ICR-4461

Бренды по названию

Популярные бренды

Advantech ICR-4461, Руководство пользователя

Результаты поиска

Содержание ICR-4461

Отзывы:

Похожие инструкции для ICR-4461

Бренды по названию

Популярные бренды