Advantech ICR-4453 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 52

background image

ICR-4453

2.8

USB Port

There is one USB 2.0 host port with socket of USB-A type.

The USB port is disabled on overload to prevent its damage (connected device is trying to get
too high current). The port is enabled again after the reboot of the router.

Mounting USB Flash Drive to the System

It is necessary to mount the USB flash drive to be able to access it in the system of the

router. Follow these steps to mount the drive:

•

Use the

dmesg

command to see the list of recently connected devices.

•

In the output of the command find out the entry for the microSD card, for example:

sda: sda1

•

To mount the card to to

mnt

directory, use the

mount

command:

mount /dev/sda1 /mnt

For more information about the commands for creating, mounting, checking and unmounting
a file system on a USB Flash Drive, see the application note for

user module.

USB Socket Pinouts

USB socket pinouts is described in Figure

and Table

Figure 12: USB Connector Pinnout

Pin

Signal mark

Description

Data flow direction

1

+5 V

Positive pole of 5 V DC supply voltage, 0.5 A

2

USB data -

USB data signal – negative pole

Input/Output

3

USB data +

USB data signal – positive pole

Input/Output

4

GND

Negative pole of DC supply voltage

Table 9: USB Connector Pinnout

21

«
...
25
26
27
28
29
...
»

Содержание ICR-4453





















































Отзывы:

Нет отзывов

Похожие инструкции для ICR-4453

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

SmartSwitch Router

Бренд: Cabletron Systems Страницы: 338

Бренд: TP-Link Страницы: 3

Бренд: Oracle Страницы: 24

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Бренд: Netis Страницы: 16

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

RCO-3000 Series

Бренд: C&T Solution Страницы: 96

Бренд: TRENDnet Страницы: 62

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренд: Nakayo Страницы: 119

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

Бренд: Nilox Страницы: 66

PG-Flex FLC-704

Бренд: PairGain Страницы: 20

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Бренд: Hamlet Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды