Advantech ICR-4453 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 52

background image

ICR-4453

2.5

Power Supply

Two pin terminal connector with 3.5 mm pitch is used to power the router. Corresponding

connector is supplied with the router as a standard accessories.

Pin

Signal mark

Description

1

VCC(+)

Positive pole of DC supply voltage (+9 to +48 V DC)

2

GND(-)

Negative pole of DC supply voltage

Table 4: Power connector pinout

Figure 8: Power Connector Pinout

Required power supply voltage for the router is b9 V and +48 V DC, see the

connection scheme on Figure

. Protection against reversed polarity without signaling is built

into the router. For correct operation it is necessary that the power source is able to supply
power of 18 W (non-PoE version).

If the negative pole of the router is grounded, there is no protection against reversed
polarity! The only protection left is the fuse inside the device. Only the service center can
restore the router’s functionality.

The power voltage for the PoE router version must be 48 V DC to work as the PoE PSE
device.

In applications requiring low power consumption (such as solar power - not 7/24 mode)
is strictly recommended to use the Low Power Mode (LPM) mode prior to powering down
the entire router.

17

«
...
21
22
23
24
25
...
»

Содержание ICR-4453





















































Отзывы:

Нет отзывов

Похожие инструкции для ICR-4453

Бренд: IBM Страницы: 72

Бренд: D-Link Страницы: 29

DGS-3700 Series

Бренд: D-Link Страницы: 292

Бренд: D-Link Страницы: 140

DGS-1224T - Web Smart Switch

Бренд: D-Link Страницы: 61

DI-LB604 - Load Balancing Router

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 45

Бренд: D-Link Страницы: 218

DES-3528 - xStack Switch - Stackable

Бренд: D-Link Страницы: 322

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 10

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 4

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 13

DI-804HV - Express ENwork Router

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды