Advantech B+B SmartWorx IE-iMcV-2xLIM Скачать руководство пользователя страница 4

 

IE-iMcV-2xLIM 

 

 

FCC RADIO FREQUENCY INTERFERENCE STATEMENT 

 

This equipment has been tested and found to comply with the limits for a Class B 

computing device, pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference when the 

equipment is operated in a commercial environment. This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause harmful interference to radio 

communications. Operation of this equipment in a residential area is likely to 

cause harmful interference in which the user will be required to correct the 

interference at his own expense. Any changes or modifications not expressly 

approved by the manufacturer could void the user’s authority to operate the 

equipment. 
 
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI 

limits. This digital apparatus does not exceed the Class B limits for radio noise 

emission from digital apparatus set out in the Radio Interference Regulation of 

the Canadian Department of Communications. 
 
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant 

les limites applicables aux appareils numériques de classe B prescrites dans le 

Règlement sur le brouillage radioélectrique publié par le ministère des 

Communications du Canada. 

 
 

ABOUT THIS MANUAL 

 

 2018 B+B SmartWorx. All rights reserved. Information in this manual is subject 

to change without notice and does not represent a commitment on the part of 

B+B SmartWorx. B+B SmartWorx assumes no responsibility for errors that may 

appear in this document. B+B SmartWorx shall not be liable for incidental or 

consequential damages resulting from the furnishing, performance or use of this 

manual.  
 
No part of this publication may be reproduced or transmitted in any form or by 

any means, electronic or mechanical, including photography, recording or any 

information storage and retrieval system without written consent.  
 
Other brands or product names used in this manual may be registered 

trademarks and the property of their respective owners. The use of trademarks or 

other designations in this publication is for reference purposes only and does not 

constitute an endorsement by the trademark holder. 
 

 

 

Содержание B+B SmartWorx IE-iMcV-2xLIM
















Отзывы: