background image

ACP-2000MB User Manual

iv

18.

This device complies with Part 15 of the FCC rules. Operation is subject to the 
following two conditions: 

        (1) this device may not cause harmful interference, and 
        (2) this device must accept any interference received, including
              interference that may cause undesired operation.

19.

CAUTION:

 Always completely disconnect the power cord from your chassis 

whenever you work with the hardware. Do not make connections while the 
power is on. Sensitive electronic components can be damaged by sudden 
power surges. 

20.

CAUTION: 

Always ground yourself to remove any static charge before touching 

the motherboard, backplane, or add-on cards. Modern electronic devices are 
very sensitive to static electric charges. As a safety precaution, use a grounding 
wrist strap at all times. Place all electronic components on a static-dissipative 
surface or in a static-shielded bag when they are not in the chassis.

21.

CAUTION: 

Any unverified component could cause unexpected damage. To 

ensure the correct installation, please always use the components (ex. screws) 
provided with the accessory box.

A Message to the Customer                                                  

Advantech customer services

Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known. Your satisfaction is our primary concern. Here is a guide to Advantech's cus-
tomer services. 
To ensure you get the full benefit of our services, please follow the instructions below
carefully.

Technical support

We want you to get the best performance possible from your products. If you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
Please consult this manual first. If you still cannot find the answer, gather all the infor-
mation or questions that apply to your problem, and with the product close at hand,
call your dealer. Our dealers are well trained and ready to give you the support you
need to get the most from your Advantech products. In fact, most problems reported
are minor and can be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice about application requirements or spe-
cific information on the installation and operation of any of our products.

Содержание ACP-2000MB





































Отзывы: