manualshive.com logo in svg

Advantage Controls RT, Инструкция по установке, обслуживанию и ремонту

Поделиться
Скачать
Advantage Controls RT Скачать руководство пользователя страница 7

7

 

 

5. 

Foot valve installation

A  weight  is  provided  to  hold  the  tubing  and  foot  valve  in  a  vertical  position  at  the  

bottom of the tank. 

Do not allow the foot valve to lay horizontally in the chemical 

 

container.

 This  defeats the action of the valve and causes the pump to lose prime. 

Keep suction tubing reasonably short and avoid high spots or bends.

 

 

6. 

Injection valve installation

The injection valve is designed to prevent a back flow and to inject chemical into the 

line. To work properly, this valve must be mounted within 45 degrees of vertical (see 

drawing). One end of the injection valve is /2” MNPT. Install this end into the piping 

system. Use Teflon tape on this fitting only. Connect the pump’s discharge tubing to 

the opposite end of the injector.   Do not use Teflon tape or joint compound on this  

fitting. Connect tubing between this fitting and the pump discharge fitting at the pump 

head.

       80
  Variation
Acceptable

     Flow

         DO NOT
    Use Teflon Tape
On Machine Threads

            USE
    Teflon Tape On 
These Threads Only

   Injection 
Check Valve

Pipe Cross
  Section

 

NOTE:   When installation is made into a line with zero pressure or when pumping into an    

    open vessel, use our three-function valve to prevent syphoning. 

 

 

 

7. 

Optional Three Function Valve.

Anti-siphon

 feature allows metering of liquids “down hill” or into the suction side of 

a circulating pump. It provides protection against an accidental application of suction 

pressure at the fluid injection point. Its Teflon coated diaphragm provides a positive 

anti-siphon action.

Back pressure

 function permits metering into atmospheric discharge (open container) 

without overpumping.

Line check

 permits removal of discharge tubing without release of system fluid.

 

 

8. 

Priming/bleed valve connection

Connect the clear poly tubing to the outlet of the bleed or priming valve. Position the 

free end of this tube in the chemical container.  Standard head configurations include a 

priming valve built into the head.  Clear poly tubing should be connected to the outlet of 

this valve, the other end of the tube should be placed in the chemical container above 

the fluid level.

Содержание RT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды