Advantage Controls RT Скачать руководство пользователя страница 3

Страница: 3 / 20

Introduction

This manual covers all facets of operation of the Advantage MicroTron™ pump, including unpacking,

mounting, electrical and plumbing connection, and start-up. Safety, maintenance and repair, warranty, and

factory information is also provided. Please read this manual completely before proceeding. Observe safety

protocols and heed all warnings and precautions.

Model Numbering

MicroTron™ Series R pump model numbers define the output, pressure and control functions present on a

particular pump. Your pump may be supplied with one or more of the options described in this manual.

To determine what features apply to your pump, check the model number label located on the pump.

Model Number Example

R T 30 X 1 – P V C 1 - S

Control Function

Dual Biocide Timers,

Dual Percent Timers &

Dual Water Meter Pulse Timers

Output

30 gallons per day at 0 psi

55 gallons per day at 75 psi

5 gallons per day at 50 psi

7 gallons per day at 250 psi

Stop Function Options

Standard

Auto Stop

Flow Switch Assembly

Flow Switch

Voltage

5 volt with USA plug (standard)

220 volt no plug

220 volt with specified plug

5 volt with US plug and no control relay pigtail

Pump Head Material

Glass-Filled Polypropylene (standard)

Kynar

PVC

Stainless

Seat Material

Viton (standard)

Teflon

Hypalon

Check Ball

Ceramic (standard)

Ceramic single on discharge

Stainless

Tubing Connections

3/8” PE, models up to 50 psi (standard)

¼” PE, 250 psi models (standard)

¼” MNPT

3/8” Clear flexible suction tubing

Special Options

3-function injection valve

NOTE: This list represents our most popular options. If you have an option not covered, contact the factory

or your dealer for more details.

Содержание RT





















Результаты поиска

Содержание RT

Отзывы:

Бренды по названию

Популярные бренды

Advantage Controls RT, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание RT

Отзывы:

Бренды по названию

Популярные бренды