manualshive.com logo in svg

Advantage Controls MicroTron, Руководство пользователя, Страница: 3 / 24

Поделиться
Скачать
Advantage Controls MicroTron Скачать руководство пользователя страница 3

3

I. Introduction

MicroTron controllers are microprocessor based menu driven units for control of recirculating and other

water applications. All settings are entered into the controller through a simple front panel keypad which

includes relay test keys.

Model Numbering

MicroTron controllers have several base functions and optional features available. Your unit may be supplied 

with one or more of the options that are described in this manual. To determine what features apply to your 

unit, check the model number label located on the controller enclosure.

Base Functions 

All model numbers can be broken down as follows 

and will start with an 

M

 or 

L

.

M

 

MicroTron with a VFD display

L

 

MicroTron with an LCD display

C

 

Conductivity Control

C-0

  Conductivity Monitor only

C-2

  Adds make-up conductivity function

F

 

Single programmable feed timer

F-2

  Dual feed timers

F-3

  Triple feed timers

F-4

  Quadruple feed timers

F-5

  Five feed timers

B

 

Single 28 day timer

B-2

  Dual 28 day timers

B-3

  Triple 28 day timers

B-4

  Quadruple 28 day timers

P

 

pH control

P-0

  pH monitor only

P-2

  pH control with dual set points

R

 

ORP control

Optional Features

This list represents our most popular options.

A

 

Conduit connections

A-6

  On/Off power switch

A-7

  Lower enclosure

C-1

  0-5V non-isolated output

C-4

  Single 4-20mA non-isolated output

C-6

  Single isolated 4-20mA output

D

 

220 V service (conduit only)

E

 

Mounted flow switch assembly

M

 

Alarm relay options

M-1S

 Sonic alarm buzzer with silence switch

N

 

Non standard conductivity scales

Q

 

Alternate electrodes

R

 

Molex connector on conductivity electrode

V

 

Digital input for bleed-off water meter

W

 

Power relay 1.5 HP max, 25 amps

X

 

Tank low level alarms

Y

 

Bleed flow alarm (requires flow switch)

Z-6

  One water meter input for each chemical

 

feed timer

Z-11

  Lockout chem feed with low conductivity alarm

9

 

Paddle wheel flowmeter input

Note:

 The list of functions and options represents past and current offerings.

Some of these may no longer be available on new units, but are listed for reference.

Содержание MicroTron

























Отзывы:

Нет отзывов