Advantage Controls MicroTron Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 24

Advantage Controls MicroTron Скачать руководство пользователя страница 20

20

During normal operations the controller will be in the RUN mode where current values are displayed. If left in

the SET UP mode the display will revert to the RUN mode screen if no keys are touched for 3 minutes. If an

alarm is present it will be flashed on the screen in the RUN mode.

While in the RUN mode if you hit the down arrow the following items may be shown:

COND

Current conductivity value.

PH

Current pH value.

ORP

Current ORP value.

TEMP

Current water temperature.

DAY-TIME

Current day of the week and time.

DATE

Current date.

BLEED TIME

If bleeding, how long it has been bleeding off.

CHEM (A)

If a chemical feed relay is on, how long it has been on.

GALLONS

If a water meter is being use, total number of gallons made up.

WATER METER

If a water meter is being used, number of contacts

BLEED METER

If a bleed-off water meter is being used, total number of gallon. If bleed/pulse = 0

bleed pulses is displayed otherwise bleed gallons

VI. Maintenance

«
...
18
19
20
21
22
...
»

Содержание MicroTron

























Отзывы:

Нет отзывов