background image

16

IX. Trouble Shooting

PROBLEM

CAUSE

REMEDY

Pump does not achieve 

or maintain prime

Air trapped in suction line

Foot valve contaminated or improperly 

installed

Excessive lift

Suction fittings not properly tightened

Worn or contaminated check valves

Split or pinch in suction tube

Low chemical level

Straighten suction line so as to eliminate 

high spots.

Inspect foot valve screen and assure that 

foot valve is in a  vertical position below  

fluid level.

Maximum suction lift is 5 feet with water  or  

fluids of  similar specific gravity; less  with 

heavier liquids such as acids. Mount pump 

in a lower position relative to the chemical 

container.

Check  fittings.  Overtightening  may  cause 

restriction. Conversely, if 

any

 leakage occurs, 

pump will suck air and fail to prime.

Inspect check valves in fluid end for cleanliness.  

Clean or replace as necessary.

Inspect suction tube through its full length 

to assure that there are no splits at the 

connections or other restrictions.  Move 

any objects or equipment which impinges 

upon suction tube or reroute as required to  

assure a smooth transition from foot valve 

to  pump.

Check fluid level in chemical supply tank.

Insufficient fluid

Stroke adjustment set too low

Worn or contaminated check valves

Obstruction in suction line

Clogged foot valve screen

Output (system) pressure too high

Diaphragm worn or torn

Electronic failure

Check operation of stroke limiter knob. 

If pump delivers too low adjustable rate, 

check settings.  Readjust as required.

Inspect, clean or  replace as necessary.

Check suction line for obstructions, clogging,     

kinks or pinch points.

Clean or replace foot valve screen.

Relocate the injector to a lower pressure part 

of the the system.

Replace diaphragm, making sure that it is 

screwed on fully to shoulder of shaft.

Consult dealer or factory.

Содержание MicroTron A Series





















Отзывы: