Advantage Controls 200 Series Скачать руководство пользователя страница 8

Страница: 8 / 24

TDS / Conductivity Cell Wiring

For accurate TDS / Conductivity readings, the cell should be installed in a tee fitting where a continuous flow

of water passes over the cell and no air can be trapped around the cell. Refer to the figure below for example

installation and page 5 for wiring. The feed cell is connected with 5 wires to terminal strip P16. The permeate

cell is connected with 5 wires to terminal strip P17. Connect each colored wire to the terminal labeled with

the same color.

Pressure Sensor Wiring

Optional 2-wire 4-20mA pressure sensors can be connected to the controller. Refer to the figures on page

5 for terminals strip locations and a sample wiring diagram. The controller supplies 24VDC to operate the

sensors.

TDS/Conductivity Sensor Installation

FLOW

TRAPPED AIR

IDEAL

GOOD

POOR

• The sensor fitting is 3/4” male NPT

• Position the sensor so air will not

be trapped around sensor.

Содержание 200 Series

























Результаты поиска

Содержание 200 Series

Отзывы:

Бренды по названию

Популярные бренды

Advantage Controls 200 Series, Руководство пользователя

Результаты поиска

Содержание 200 Series

Отзывы:

Бренды по названию

Популярные бренды