background image

ZDW103 Instructions, Release 1.1

P/D 102406

HomePro

by ADVANCED CONTROL TECHNOLOGIES, INC.

0703-01

1

Radio Frequency Controlled, 800W, 120 VAC,

Wall Mounted 3-Way Dimmer Receiver, Release 1.1

ZDW103

ZDW103 WALL MOUNTED DIMMER

The ZDW103 Wall Mounted Dimmer is a component of the HomePro lighting control system.   Wire the Wall Mounted
Dimmer in place of the standard wall switch according to the diagram above and program from the Wireless Controller
to operate loads.   Inclusion of the ZDW103 Wall Mounted Dimmer on the ZTH100 Wireless Controller menu allows
remote ON/OFF control and dimming of lights connected.
This Wall Mounted Dimmer is designed to work with other Z-Wave enabled devices.  Z-Wave nodes of other types
can be Included in the network and will also act as repeaters to increase the range of the network.
There are no field repairable assemblies on this unit. If service is needed, the unit must be returned where purchased.

DANGER!  SHOCK HAZARD. 

 Read and understand these instructions before installing.  This device is intended for

installation in accordance with the National Electric code and local regulations in the United States, or the Canadian
Electrical Code and local regulations in Canada.  It is recommended that a qualified electrician perform this installation.

To reduce the risk of overheating and possible damage 

to other equipment, do not install to control a

receptacle, a motor operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance, but

only permanently installed incandescent lamp fixtures

.  Make sure the lamp(s) to be controlled directly from the

dimmer receiver total no more than 800 watts.  Retain instructions for future use.

INSTALLATION

STEP 1.

    With power off, wire this ZDW103 and AS101’s according to the diagram show.   AS101’s are required

to be wired to the same line (or neutral) which is also wired to the master unit as well as the load being
controlled, and not wired to any other neutral. If multiple neutral wires are tied together in one box separate
the neutrals to preserve the integrity of the ZDW103 circuit.  If more than one ZDW103 is to be installed
in a wall box, scored tabs on the side can be broken off by bending back and forth with pliers, to
accommodate proper fit.  Apply power when completed.

HomePro

RF Home Automation

Supplied with matching

decorative switch plate

Note:

  This module must be “Included in the

Network” 

only where it will be permanently

installed

.  The proper operation of  this node in the

mesh network is dependent on it knowing its
location with respect to other nodes.  You cannot
“test bench” configure this module.

Содержание HomePro ZDW103








Отзывы: