Advance acoustic 56511710, Инструкция по эксплуатации

Страница: 27 / 56

4/2017 A - 27 56091206 - CS7010
ENGLISH - A INSTRUCTIONS FOR USE
SCRUBBING
WARNING!
Be sure you understand the operator controls and their functions.
While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills.
Follow the instructions in “Preparing the Machine for Use” section of this manual. Start the engine following the instructions in the appropriate
“Starting the Engine” section (Engine models).
1. While seated on the machine, adjust the seat and steering wheel (tilt steering is optional) to a comfortable operating position.
2. Release the Parking Brake (38) . To transport the machine to the work area, apply even pressure with your foot on the front of the Drive Pedal (37) to
go forward or the rear of the pedal for reverse. Vary the pressure on the foot pedal to obtain the desired speed.
3. SEE FIGURE 12. Press and hold the Solution Switch (U) to pre-wet the fl oor, solution will be dispensed while the switch is held. NOTE: This will
help prevent scarring of the fl oor surface when starting to scrub with dry brushes. This must be done prior to pressing the One-Touch™ Scrub Switch
(R) .
4. Press the One-Touch Scrub ON Switch (R) once for Regular Scrub. Press the Scrub Pressure Increase Switch (Q) once for Heavy Scrub or
twice for Extreme Scrub mode. The solution fl ow has settings that coincide with the scrub pressure, it will increase and decrease along with
the scrub pressure.
NOTE: The solution fl ow rate can also be increased or decreased independently of the scrub pressure by pressing the Solution Flow
Increase Switch (T) or Solution Flow Decrease Switch (V) , observe the Solution Flow Rate Bar Graph (C10) (see Control Panel). Any
subsequent scrub pressure adjustments will reset the solution fl ow rate to default.
5. When the One-Touch Scrub ON Switch (R) is selected, the brushes and squeegee are automatically lowered to the fl oor. The scrub, solution,
vacuum and detergent (EcoFlex models) systems are all automatically enabled and will start when the Drive Pedal (37) is activated. Any
individual system can be turned OFF or back ON by simply pressing its switch at any time during scrubbing.
NOTE: When operating the machine in reverse the squeegee automatically raises.
6. Begin scrubbing by driving the machine forward in a straight line at a normal walking speed and overlap each path by 2-3 inches (50-75 mm).
Adjust the machine speed and solution fl ow when necessary according to the condition of the fl oor.
NOTE: While scrubbing the maximum machine speed can be set by pressing the Speed Limiter Switch (K) . Adjust the machine to the
desired speed using the Drive Pedal (37) then press the Speed Limiter Switch (K) . The operator can now press the pedal all the way forward
without increasing the machine speed thereby reducing operator fatigue. The machine Speed (C5) is shown on the display.
CAUTION!
To avoid damaging the fl oor, keep the machine moving while the brushes are turning (the brushes will turn OFF after a 2 second
delay when the drive pedal is placed in the neutral position).
7. When scrubbing, check behind the machine occasionally to see that all of the waste water is being picked up. If there is water trailing the
machine, you may be dispensing too much solution, the recovery tank may be full, or the squeegee tool may require adjustment.
8. The machine defaults to the last cleaning mode used Minimum or Maximum Concentration Detergent (if detergent is installed and was
activated). Press the Burst of Power Speed (S) to override the current cleaning mode and temporarily increase scrub pressure, solution
fl ow and the detergent ratio (unless in Maximum Concentration). This will cause the Burst of Power Indicator (C34) to be displayed along
with a countdown timer for one minute, solution fl ow rate will increase to the next level, scrub pressure will increase to the next level and the
detergent ratio will be at the Maximum Concentration level (detergent system will be turned on at Minimum Concentration level if it was off).
NOTE: Repeatedly pressing and releasing the Detergent Switch (X) will cycle between Minimum Concentration, Maximum Concentration and
detergent off. The EcoFlex system will only function if the scrub system (R) has been enabled.
9. For extremely dirty fl oors, a one-pass scrubbing operation may not be satisfactory and a “double-scrub” operation may be required. This
operation is the same as a one-pass scrubbing except on the fi rst pass the squeegee and scrub deck blades are in the up position (press the
Vacuum/Wand Switch (W) to raise the squeegee). The Side Skirts (8 and 39) can also be raised for double scrubbing if needed and held in
place with the Catch (AE) shown in Figure 6. This allows the cleaning solution to remain on the fl oor to work longer. The fi nal pass is made
over the same area, with the squeegee and side blades lowered to pick up the accumulated solution.
10. The recovery tank has two Vac Motor Inlet Shut-Off Floats (52) that cause ALL systems to turn OFF except the drive and sweeping systems
when the recovery tank is full. When the fl oat(s) is activated, the recovery tank must be emptied. The machine will not pick up water or scrub
with the fl oat activated. The machine can continue to be used for sweeping.
NOTE: The Recovery Tank Full Indicator (C21) appears on the LCD Display (C) when the switch is activated.
11. When the operator wants to stop scrubbing or the recovery tank is full, press the One-Touch Scrub Switch (R) once. This will automatically
stop the scrub brushes and solution fl ow and the scrub deck will raise up. The squeegee will raise up after a brief delay and the vacuum will
stop after an additional delay (this is to allow any remaining water to be picked up without turning the vacuum back on).