background image

9

12

12A

10

CHARGING GEL/AGM (VRLA) BATTERIES

Charge the batteries each time the machine is used or when the Battery Charge Level Indicator 

(C3)

 is reading less than full.

 WARNING!

Charge batteries in a well-ventilated area. If battery acid makes contact with your skin, 

fl

 ush the affected area with water for 5 

minutes and seek medical attention.
Do not smoke while servicing the batteries.

If your machine shipped with an onboard battery charger do the following:

Turn the machine off at the Power Switch 

(B)

.

See Figure 12.

  Raise the steering column to the full upright position.  Tip the seat forward and engage the Seat Prop Rod 

(9)

 for battery, charger access and 

proper ventilation.

Unwind the electrical cord for the onboard charger and plug it into a properly grounded outlet.  Refer to the OEM product manual for more detailed operating 
instructions.  While AC power is applied to the onboard charger all machine functions are disabled.

The Battery Charge Status Indicator 

(C19)

 will begin showing the batteries’ state of charge.  This indicates that the charging cycle has begun.  As the 

charging cycle continues, the battery charge level will 

fi

 ll in.

When the Battery Charge Status Indicator 

(C19)

 is completely 

fi

 lled, the machine senses fully charged batteries, however the charging process may not be 

complete.  Rely on the status lights on the Charger 

(12)

 (and its OEM manual) to verify when the batteries are completely charged.  This may take several 

hours depending upon the condition of the batteries before charging.

After charging is complete unplug the charger and wind up the Cord 

(12A)

.  Wait at least 10 seconds before turning on the machine after unplugging the 

charger.

If your machine shipped without an onboard battery charger do the following:

Turn the machine off at the Power Switch 

(B)

.

See Figure 12.

  Raise the steering column to the full upright position.  Tip the seat forward and engage the Seat Prop Rod 

(9) 

for battery access and proper 

ventilation.

Disconnect the batteries from the machine and push the connector from the charger into the Machine Battery Connector 

(10)

.  Follow the instructions on the 

battery charger.  

SERVICE

 

NOTE:  

Make sure you plug the battery charger into the connector that attaches to the batteries.

IMPORTANT:  Make sure you have an appropriate charger for use on Gel cell batteries.  Use only “voltage-regulated” or “voltage-limited” chargers.  
Standard constant current or taper current chargers MUST NOT be used.  A temperature-sensing charger is recommended, as manual adjustments are 
never accurate and will damage any VRLA battery.

FIGURE 12

When Servicing Batteries...
*

 

Remove all jewelry

*

 

Do not smoke

*

 

Wear safety glasses, rubber gloves and a rubber apron

*

 

Work in a well-ventilated area

*

 

Do not allow tools to touch more than one battery 
terminal at a time

*

 

ALWAYS disconnect the negative (ground) cable 

fi

 rst 

when replacing batteries to prevent sparks.

*

 

ALWAYS connect the negative cable last when installing 
batteries.

 CAUTION!

Your valve regulated lead acid (VRLA) battery 
will deliver superior performance and life ONLY 
IF IT IS RECHARGED PROPERLY!  Under or 
overcharging will shorten battery life and limit 
performance.  Be sure to FOLLOW PROPER 
CHARGING INSTRUCTIONS!  DO NOT ATTEMPT 
TO OPEN THIS BATTERY!  If a VRLA battery 
is opened, it loses its pressure and the plates 
become oxygen contaminated.  THE WARRANTY 
WILL BE VOIDED IF THE BATTERY IS OPENED.

C19

4/2016

A - 25

 56091161 - SC6000

ENGLISH - A

INSTRUCTIONS FOR USE

For cleaning machines, parts & supplies click/visit www.southeasternequipment.net

For cleaning machines, parts & supplies click/visit www.southeasternequipment.net

Содержание 56116000





































Отзывы: