background image

4

Section 61246026L6-5, Issue 2

61246026L6-5B

Pin

Designation

Description

 1 ........ CH GND ....... Chassis ground

 5 ........ DS1-T1 ......... DS1  receive  out  tip  (to  customer

interface)

 7 ........ H1-T ............. HDSL Loop 1 tip (facility)

11 ....... CH GND ....... Chassis ground

12 ....... GND .............. Ground for protection switching

13 ....... H1-R ............. HDSL Loop 1 ring (facility)

15 ....... DS1-R1 ......... DS1  receive  out  ring  (to  customer

interface)

20 ....... VCC .............. +5VDC for protection switching

27 ....... CH GND ....... Chassis ground

32 ....... PROT-4 ......... Control line for protection switching
34 ....... PROT-3 ......... Control line for protection switching
38 ....... PROT-2 ......... Control line for protection switching
40 ....... PROT-1 ......... Control line for protection switching
41 ....... H2-T ............. HDSL Loop 2 tip (facility)

47 ....... H2-R ............. HDSL Loop 2 ring (facility)

49 ....... DS1-R ........... DS1  transmit  in  ring  (from  customer

interface)

55 ....... DS1-T ........... DS1  transmit  in  tip  (from  customer

interface)

Table D.  Card Edge Pin Assignments

Figure 2.  P1 Jumper Location

Switch

Label

Function

REM .......... Pressing this switch changes the HTU-C customer

loopback state as follows:

• If the HTU-C 

is not

 in loopback, pressing REM

activates

 the loopback.

• If  the  HTU-C 

is

  in  loopback,  pressing  REM

deactivates

 the loopback.

LOC ........... Pressing this switch changes the HTU-R customer

loopback state as follows:

• If the HTU-R 

is not

 in loopback, pressing LOC

activates

 the bilateral loopback.

• If  the  HTU-R 

is

  in  loopback,  pressing  LOC

deactivates 

the bilateral loopback.

Table C.  Front Panel Loopback Switches

3.  CONNECTIONS

All connections of the HTU-R are made through
card edge connectors.  Table D gives the card edge
pin assignments for the HTU-R circuit pack.

When the circuit pack is installed in any of the
HTU-R enclosures, all connections are made
through the enclosure backplanes.  See the
following ADTRAN Installation and Maintenance
practices for more information:

Number

Description

61242007L1-5 .......... HR12 Installation and

Maintenance

61242008L1-5 .......... HR4 Installation and

Maintenance

61242034L2-5 .......... T400 Single Mount

Installation and Maintenance
(removable RJ-48 jacks)

61245034L1-5 .......... T200 Dual-slot Installation

and Maintenance (APS
Housing)

Caution:  Ensure chassis ground is properly
connected  for  either  standalone  or
shelf-mounted applications.

4.  HDSL SYSTEM TESTING

The T200 HTU-R provides diagnostic, loopback,
and signal monitoring capabilities.

The seven front panel LEDs provide diagnostics for
HDSL loops, DS1 signals, alarms, provisioning, and
loopbacks.  See subsection 2 of this practice for
details.

The HTU-R provides local and remote loopback
capabilities via the loopback switches or through the
craft interface port (DB9) on the faceplate.

The DS1 MON jacks provide a non-intrusive access
for DS1 signal monitoring.

LBO

P1

0        - 15

Содержание T200 FNID
























Отзывы: