2
61287735G3-22B
2. Refer to the illustration below and connect the twisted-pair Tip
(green) and Ring (Red) to the RJ-11 connector using an RJ-11
crimper.
3. Insert the RJ-11 connector in the appropriate POTS 1 or POTS 2
jack.
Connecting Ethernet
The SFU ONT supports four 1 Gigabit (10/100/1000Base-T) connec-
tions (LAN 1 to LAN 4).
If Ethernet cables are not available, use the following procedure and
table to create the Ethernet cables:
1. Trim the insulation for the subscriber Ethernet cable.
2. Connect the wires per the following table using an RJ-45
Crimper.
3. Insert the CAT 6 rated cable in the appropriate LAN 1 through
LAN 4 ports.
Installing Fiber
CAUTION
!
LASER RADIATION
1300 nm to 1500 nm
Do not view directly with optical instruments.
This product contains a Class 1M Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1 and -2.
Fiber is installed in an SC connecter located behind a removable
protector panel on the right-rear of the SFU ONT. Refer to the figure
below when installing fiber:
1. Remove the phillips-head screw from the right side of the fiber
protector panel.
2. Slide the protector cover back to expose the SC connector.
Ethernet RJ-45 Pin-out
Pin
Name
Description
Color Code
1
TRD0+
Transmit/Receive Positive
White/
Orange
2
TRD0-
Transmit/Receive Negative
Orange
3
TRD1+
Transmit/Receive Positive
White/Green
4
TRD2+
Transmit/Receive Positive
Blue
5
TRD2-
Transmit/Receive Negative
White/Blue
6
TRD1-
Transmit/Receive Negative
Green
7
TRD3+
Transmit/Receive Positive
White/Brown
8
TRD3-
Transmit/Receive Negative
Brown
1 2 3 4
1 = Not Connected
2 = Tip
3 = Ring
4 = Not connected
Required tools
Standard technician tools and those listed below are required for
installing the SFU ONT:
■
Carpenter’s level
■
RJ-45/RJ-11 crimper
■
A telephony/data communication test set
■
PON power meter with wavelength filtering
■
Fiberscope or videoscope
■
Two #8 Pan Head screws (1 inch or greater in length)
■
Assorted tie wraps for securing cabling and wiring
For fiber optic connections, the following are required:
■
Fiber optical fusion splice tools
■
ODC Fiber cleaning tool
■
SC Fiber connector
Desk Top Installation
The SFU ONT can sit on a desktop or be wall mounted. With a desk
mount, ensure the SFU ONT is not located in direct sunlight and is
not located next to any thermal obstructions.
Wall Mount Installation
The SFU ONT can be wall-mounted.
NOTE
Refer to the illustration below when installing the SFU ONT on a wall
mount.
To wall mount the SFU ONT, perform the following steps:
1. Decide on a location for the SFU ONT.
2. Attach a 1/4 inch mounting board (typically plywood) to the
wall. If the wall is drywall construction, ensure the mounting
board is supported by the wall studs.
3. Install two #8 Pan Head screws (1 inch or greater in length)
using the key holes on the back of the SFU ONT as location
markers. Leave approximately 1/4 inch protruding from the
mounting surface.
4. Slide the SFU ONT over the Pan Head screws and exert a small
amount of downward pressure to ensure that the top of the
slots are resting on the shafts of the Pan Head screws.
Connecting POTS
If POTS cables are not available, use the following procedure to create
the POTS cables:
1. Trim the insulation for the subscriber POTS cables.
Rear of SFU ONT
