2
61287562G1-22A
1. Remove the POTS cable supplied with the Home Gateway
ONT and connect one end to the Home Gateway ONT and
the other end to a standard telephone base.
2. If a POTS cable is not available, select a standard telephone
twisted pair cable of appropriate length and trim the
insulation back approximately 1/2 inch on each end.
3. Refer to the illustration below and connect the twisted-pair
Tip (green) and Ring (Red) to the RJ-11 connectors using an
RJ-11 crimper.
4. Connect one end of the POTS cable to the Home Gateway
ONT and the other end to a standard telephone connection.
Step 3: Connect Ethernet
The Home Gateway ONT supports four Gigabit (10/100/
1000Base-T) connections. To install Ethernet to the Home
Gateway ONT, refer to the illustration on the first page and
complete the following steps:
1. Remove the Ethernet cable supplied with the Home Gate-
way ONT and attach one end to the
LAN1
connection on the
rear of the Home Gateway ONT and the other end to the
incoming Ethernet device.
2. If an Ethernet cable is not available, obtain a CAT5 or 6 cable
of appropriate length and trim the insulation back
approximately 1/2 inch on both ends.
3. Connect the wires per to an RJ-45 connector using the table
below.
4. Crimp the connector using an RJ-45 Crimper.
5. Connect one end to the appropriate
LAN1
connection on the
rear of the Home Gateway ONT and the other end to the
incoming Ethernet device.
6. Repeat these steps as necessary for each additional Ethernet
connection required.
Ethernet RJ-45 Pin-out
Pin
Name
Description
Color
Code
1
TRD0+
Transmit/Receive
Positive
White/Orange
2
TRD0
‐
Transmit/Receive
Negative
Orange
3
TRD1+
Transmit/Receive
Positive
White/Green
4
TRD2+
Transmit/Receive
Positive
Blue
5
TRD2
‐
Transmit/Receive
Negative
White/Blue
6
TRD1
‐
Transmit/Receive
Negative
Green
7
TRD3+
Transmit/Receive
Positive
White/Brown
8
TRD3
‐
Transmit/Receive
Negative
Brown
1 2 3 4
1 = Not Connected
2 = Tip
3 = Ring
4 = Not connected
POTS Pin-Outs
Installation Overview
To install the Home Gateway ONT, complete the following steps:
Step 1: Install Home Gateway ONT
Step 2: Connect POTS
Step 3: Connect Ethernet
Step 4: Connect Fiber
Step 5: Connect Power
Step 6: Connect USB
Required tools
Standard technician tools and those listed below are required for
installing the Home Gateway ONT:
3/32 inch screw driver for connecting Home Gateway ONT
power
RJ-45/RJ-11 crimper
A telephony/data communication test set
PON power meter with wavelength filtering
Fiberscope or videoscope
Two #8 Pan Head screws (1 inch or greater in length)
Assorted tie wraps for securing cabling and wiring
For fiber optic connections, the following are required:
Fiber optical fusion splice tools
ODC Fiber cleaning tool
SC Fiber connector
Installation Steps
To install the Home Gateway ONT, refer to the illustration on the
first page and complete the following steps.
Step 1: Install the Home Gateway ONT
There are two options when installing the Home Gateway ONT:
Desk Top and Wall Mount. Both are described below.
Desk Top Installation
The Home Gateway ONT can sit on a desktop or be wall
mounted. With a desk mount, ensure the Home Gateway ONT is
not located in direct sunlight and is not located next to any
thermal obstructions.
Wall Mount Installation
To wall mount the Home Gateway ONT, perform the following
steps:
1. Decide on a location for the Home Gateway ONT. Included
with the Home Gateway ONT is a 12 V Power Adaptor with
a 4-foot power cord. The installation location should be
within 4 feet of a wall outlet.
2. Remove the Mounting Bracket from the bottom of the Home
Gateway ONT.
3. Use the keyhole slots on the back of the Mounting Bracket as
a template and attach it to drywall using the appropriate
anchors.
4. Reattach the Home Gateway ONT to the Mounting Bracket.
Step 2: Connect POTS
To connect POTS, refer to the illustration on the first page and
perform the following steps:
DRAFT
