ADTRAN 1200831G1 Скачать руководство пользователя страница 25

Страница: 25 / 36

NetVanta 5305 Hardware Installation Guide

Option Modules

61200990L1-34P

Clock Source

•

Network

•

Internal

Diagnostics

•

Network Loopbacks: Line, payload, remote

•

Test Pattern Generation and Detection: QRSS, 2

- 1, 2

- 1, all ones, all zeros

Compliance

•

EMC - see

Electromagnetic Compatibility (EMC) Table on page 6

•

AS/ACIF S016

•

ETSI TBR 12/TBR 13

•

ACTA/FCC Part 68

•

IC CS-03

•

UL/CUL 60950

•

EN 60950

•

IEC 60950

•

AS/NZS 60950

•

RoHS Compliant (Telecommunications exemption)

Environmental

•

Operating Temperature: 0°C to 50°C

•

Storage Temperature: -20°C to 70°C

•

Relative Humidity: Up to 95 percent, noncondensing

Physical

•

5.63-inch W x 8.63-inch D

T1/E1 Mode Switch

The Octal T1/E1 Wide Module is shipped with the T1/E1 mode switch (located on the circuit board) set to
T1. If you require E1 functionality, use your thumbnail to slide the E1 mode switch to the

position (as

shown in the figure below).

A different service provider can be used on each interface. Each interface has an
independent clock.

No external CSU/DSU is needed with the T1/FT1 interface.

Содержание 1200831G1































Результаты поиска

Содержание 1200831G1

Отзывы:

Похожие инструкции для 1200831G1

Бренды по названию

Популярные бренды

ADTRAN 1200831G1, Руководство по установке оборудования

Результаты поиска

Содержание 1200831G1

Отзывы:

Похожие инструкции для 1200831G1

Бренды по названию

Популярные бренды