job
Aid
1
D
ESCRIPTION
The
Small
Form
‐
Factor
Pluggable
Gigabit
Ethernet,
Copper
(SFPGC)
plugs
into
ADTRAN
Gigabit
Ethernet
modules
designed
to
accept
Small
Form
‐
factor
Pluggables
(SFPs).
Installed
into
an
appropriate
host
module,
the
SFPGC
provides
1000
Mbps
full
duplex
data
‐
links
with
5
‐
level
Pulse
Amplitude
Modulation
(PAM)
signal
over
unshielded
twisted
‐
pair
Cat
5
cable.
NOTE
To
ensure
compatibility,
refer
to
the
documentation
provided
with
the
host
module.
The
following
features
are
supported
on
the
SFPGC:
♦
Up
to
1.25
Gbps
bidirectional
datal
links
♦
100
meter
maximum
distance
over
shielded
twisted
‐
pair
Cat
5
cable
CAUTION
!
Due
to
compliance
certification
requirements,
use
only
SFPs
supplied
by
ADTRAN
with
the
host
module.
ADTRAN
cannot
certify
system
integrity
with
other
SFPs.
Operational Specifications
♦
Operational
temperature
range:
–40°C
to
+65°C
♦
Operational
altitude
range:
–197
feet
(–60
meters)
to
13,000
feet
(3,962
meters)
◊
From
–197
feet
(–60
meters)
to
6,000
feet
(1,800
meters)
the
operating
temperature
is
derated
by
1.6°C/1,000
feet.
◊
From
6,000
feet
(1,800
meters)
to
13,000
feet
(4,000
meters)
the
operating
temperature
is
derated
by
1.4°C/1,000
feet.
♦
Storage
temperature
range:
–40°C
to
+100°C
♦
Relative
humidity
to
95%,
noncondensing
Small Form-Factor Pluggable Gigabit
Ethernet, Copper
I
NSTALLATION
To
install
the
SFPGC
into
an
appropriate
module,
complete
the
following
steps:
1. Inspect
the
SFPGC.
If
damaged,
file
a
claim
with
the
carrier
and
then
contact
ADTRAN
Customer
Service.
2. Remove
the
black
safety
cap
from
the
connector
of
the
SFPGC.
3. Insert
the
SFPGC
into
the
receptacle
on
the
circuit
board
of
the
host
module,
with
the
manufacturer’s
label
facing
outward.
Slide
the
SFPGC
all
the
way
into
the
receptacle.
4. Using
thumb
and
forefinger,
firmly
squeeze
the
receptacle
and
SFPGC
together,
to
ensure
a
proper
connection.
NOTE
The
latch
on
the
SFP
is
for
removal
only.
5. Continue
the
installation
and
turn
‐
up
of
the
host
module
using
the
instructions
in
the
Job
Aid
or
Installation
and
Maintenance
Guide
(I&M)
provided
with
that
module.
Both
are
available
online
at
www.adtran.com
.
P
ROVISIONING
The
SFPGC
is
not
directly
provisionable.
To
provision
the
SFPGC,
access
the
menu
system
of
the
host
module.
Refer
to
the
“Provi
‐
sioning”
section
of
the
Job
Aid
or
I&M
provided
with
the
host
module
for
provisioning
details.
COMPLIANCE
CAUTION
!
♦
Electrostatic
Discharge
(ESD)
can
damage
electronic
modules.
When
handling
modules,
wear
an
antistatic
discharge
wrist
strap
to
prevent
damage
to
electronic
components.
Place
modules
in
antistatic
packing
material
when
transporting
or
storing.
When
working
on
modules,
always
place
them
on
an
approved
antistatic
mat
that
is
electrically
grounded.
♦
The
SFPGC
is
NRTL
Listed
to
the
applicable
UL
standards.
The
SFPGC
meets
or
exceeds
all
the
applicable
requirements
of
NEBS,
Telcordia
GR
‐
63
‐
CORE,
and
GR
‐
1089
‐
CORE.
The
SFPGC
is
intended
for
deployment
in
Central
Office
type
facilities,
EEEs,
EECs,
and
locations
where
the
NEC
applies
(ex.
Customer
Premises).
Install
the
SFPGC
in
an
ADTRAN
product
located
in
a
restricted
access
location.
This
device
complies
with
Part
15
of
the
FCC
rules.
Operation
is
subject
to
the
following
two
conditions:
1. This
device
may
not
cause
harmful
interference
2. This
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
Changes
or
modifications
not
expressly
approved
by
ADTRAN
could
void
the
user
ʹ
s
authority
to
operate
this
equipment.
CLEI: SIPQ0CUF_ _
Product P/N: 1184561P4
Issue Date: May 2010
Document P/N: 61184561P4-22C
