Example 2:
Set a “Duress Code” with the number of “2 3 9 8 0” for Output 2
42
01
23980
#
(a) (b) (c) (d)
(a)
Duress Code Programming for Output 2,
(b)
Duress Code ID,
(c)
The Duress Code,
(e)
Entry Confirmation
Example 3:
Delete an Output 1 “Duress Code” from Duress Code ID
01
in the memory
41
01 #
(a) (b) (c)
(a)
Duress Code Programming for Output 1,
(b)
The Duress Code ID,
(c)
Delete Confirmation
Example 4:
Clear The Whole Group of Duress Code from Location
41
:
41
0999 #
(a) (b) (c)
a)
Group Location
41
,
b)
The Group Deletion Command,
c)
Confirmation, all Duress Codes in Location
41
are cleared.
THE OPERATION AND FUNCTION OF THE DURESS CODE
The Duress Code(s) has double actions when it is keyed in. It activates the Duress Output (for duress alarm) and at the
same time activates the specific Relay Output 1, 2 or 3 just like a normal User PIN. The Duress Code always activates
its Relay Output in its group, but, does not de-activate (stop) the Duress Output.
ONLY a normal User PIN in its group
can reset (de-activate) its Duress Output.
For Example:
Key in The Duress Code 3 3 6 9 of the Group 1 (for Output 1) To Command The Duress Function :
3369#
----- Duress Output activates (switches to (-) ground) & Output 1 activates.
Key in The Duress Code 3 3 6 9 in Group 1 (for Output 1) Again :
3369#
----- Duress Output keeps activating and no change in its state (keeps to (-) ground) &
Output 1 activates again.
Key in A Normal User PIN 1 3 6 9 in Group 1 (for Output 1):
1369#
----- Duress Output resets (back to OFF state) but has no function on Output 1.
Report Duress in EM Card Operation
The Duress Codes are Prime User Codes in the system. In the “
EM Card + Secondary User PIN
” or “
EM Card +
Common User PIN
” operation, they can be used to replace the “Secondary User PIN” or the “Common User PIN” to
operate the specific output and report a duress alarm event. Programming is not required. The system has the function
automatically while Duress Code exists.
Operation : Taking Duress Code 3 3 6 9 in Group 1 for Output 1 As Example
3369 #
(a) (b) (c)
a) Put the EM card close to the reader. One-beep confirms the reading and 30 seconds waiting time is given for the
entry of the Duress Code, the Amber LED keeps flashing
b) Key in the Duress Codes 3 3 6 9 for operating the Output 1
c) Confirm it with the # key. Output 1 activates in a normal way and the Duress Output also activates to report
Duress Event to an alarm system if connected.
NOTE:
No Duress Event can not be reported in the operation of only EM Card alone.
Read Card
22
CONFIGURATION OF THE OUTPUT MODES OF OUTPUT 1, 2 AND 3 (Locations 51, 52 & 53)
The three relay outputs of this keypad are programmable for Start/Stop or Timing modes. Apart from the door access
control, alarm arm-disarm control, they are also
universal timers for automatic operators in industry
with their
99,999 seconds (over 24 hours) programmable timer.
OUTPUT LOCATIONS
51
-- Location for Output 1
52
-- Location for Output 2
53
-- Location for Output 3
OUTPUT MODE & TIMING
0
– Start /Stop Mode (Toggle)
The number 0 sets the output to the
Start / Stop mode
. The output
Starts
when an User PIN and/or Card is entered/
read; the output
Stops
when an User PIN and/or Card is entered/read again.
1
-
99999
Seconds Momentary --- (Default -- Momentary 5 Seconds)
The output can be set in
Momentary Mode
with the time of 1 second to 99,999 seconds. The output will reset
automatically when the time expires OR it can be
RESET manually at anytime with the Super User Code
that
operates the desired output before the end of the time.
Example :
Reset Output 1 --
#
11
------------- Output 1 resets
Reset Output 2 --
#
12
------------- Output 2 resets
Reset Output 3 --
#
13
------------- Output 3 resets
PERSONAL SAFETY AND SYSTEM LOCK-OUT (Location 60)
SAFETY & LOCK-OUT OPTIONS
The Options are represented by their Mode Numbers in programming. They are described below:
1
--- After 10 successive false Card/User Code trials, the keypad locks during 30 seconds. -- (Default)
2
--- After 10 successive false Card/User Code trials, activates the Duress output to switch to (-) ground.
5
-
10
--- Selection of after 5 to 10 successive Card/User Code trials, the keypad locks during 15 minutes. The
keypad can be reset to release the lock-out with the “Super User Code” in the following way.
Example :
Release the lock-out --
#
21
00
--- Disappearance of all the above lock-out securities.
SUPER USER CODE
SUPER USER CODE
SUPER USER CODE
1 to 2 Digits
LOCK-OUT MODES
VALIDATION
LOCATION
60
#
SUPER USER CODE
OUTPUT MODE & TIME
VALIDATION
LOCATIONS
51
-
53
0
or
1
-
99999
#
23
