manualshive.com logo in svg

ADLINK Technology NuPRO-720, Руководство пользователя

Поделиться
Скачать
ADLINK Technology NuPRO-720 Скачать руководство пользователя страница 86

74

POST Messages

DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN
SETUP 

Type of diskette drive installed in the system is different from
the CMOS definition. Run Setup to re-configure the drive type
correctly.

DISPLAY SWITCH IS SET INCORRECTLY 

Display switch on the motherboard can be set to either mono-
chrome or color. This indicates the switch; is set to a different
setting than indicated in Setup. Determine which setting is cor-
rect, then either turn off the system and change the jumper, or
enter Setup and change the VIDEO selection.

FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT 

Cannot find or initialize the floppy drive controller. Make sure
the controller is installed correctly and firmly. If there are no
floppy drives installed, be sure the Diskette Drive selection in
Setup is set to NONE.

KEYBOARD ERROR OR NO KEYBOARD PRESENT

Cannot initialize the keyboard. Make sure the keyboard is
attached correctly and no keys are being pressed during the
boot. If you are purposely configuring the system without a key-
board, set the error halt condition in Setup to HALT ON ALL,
BUT KEYBOARD. This will cause the BIOS to ignore the miss-
ing keyboard and continue the boot.

OFFENDING ADDRESS NOT FOUND 

This message is used in conjunction with the I/O CHANNEL
CHECK and RAM PARITY ERROR messages when the seg-
ment that has caused the problem cannot be isolated.

OFFENDING SEGMENT 

This message is used in conjunction with the I/O CHANNEL
CHECK and RAM PARITY ERROR messages when the seg-
ment that has caused the problem has been isolated.

Содержание NuPRO-720



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды