background image

14

Important Safety Instructions

Leading

EDGE COMPUTING

Never attempt to repair the device, which should only be 
serviced by qualified technical personnel using suitable 
tools

A Lithium-type battery may be provided for uninterrupted 
backup or emergency power.

The device must be serviced by authorized technicians 
when:

The power cord or plug is damaged

Liquid has entered the device interior

The device has been exposed to high humidity and/or 
moisture

The device is not functioning or does not function 
according to the User’s Manual

The device has been dropped and/or damaged and/or 
shows obvious signs of breakage

Disconnect the power supply cord before loosening the 
thumbscrews and always fasten the thumbscrews with a 
screwdriver before starting the system up

It is recommended that the device be installed only in a 
server room or computer room where access is:

Restricted to qualified service personnel or users familiar 
with restrictions applied to the location, reasons therefor, 
and any precautions required

Only afforded by the use of a tool or lock and key, or 
other means of security, and controlled by the authority 
responsible for the location

CAUTION:

Risk of explosion if battery is replaced with one of an incorrect 
type; please dispose of used batteries appropriately. 

Risque d’explosion si la pile est remplacée par une autre de 
type incorrect. Veuillez jeter les piles usagées de façon appro-
priée.

Содержание DIN-1040




























Отзывы: