ADLINK Technology CoreModule 745 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 56

background image

Chapter 2

Product Overview

14

Reference Manual

CoreModule 745

Specifications

Physical Specifications

provides the physical dimensions of the CoreModule 745.

Table 2-4. Weight and Footprint Dimensions

Item

Dimension

NOTE

Overall height is measured from the
upper board surface to the highest
permanent component (PC/104 bus
connector) on the upper board surface.
This measurement does not include the
heatsink, which can vary. The heatsink
could increase this dimension.
Component height should not exceed
0.345" (8.763mm) from the upper
surface of the board and 0.190"
(4.826mm) from the lower surface of the
board. See

for the stack

heights of the heatsinks on the board.

Weight

0.12 kg (0.25 lbs)

Height (overall)

11.05 mm (0.435 inches)

Board thickness

2.362 mm (0.093 inches)

Width

96.01 mm (3.78 inches)

Length

115.57 mm (4.55 inches)

«
...
18
19
20
21
22
...
»

Содержание CoreModule 745

























































Отзывы:

Нет отзывов

Похожие инструкции для CoreModule 745

Бренд: Yamaha Страницы: 96

Бренд: Gigabyte Страницы: 74

Бренд: AOpen Страницы: 96

Бренд: Intel Страницы: 78

Бренд: Gigabyte Страницы: 18

Бренд: XMOS Страницы: 20

EVAL-6ED100HPDRIVE-AS

Бренд: Infineon Страницы: 14

Бренд: Lucky Star Страницы: 77

Бренд: Fastfame Страницы: 41

Бренд: Maxus Страницы: 59

Бренд: CHAINTECH Страницы: 49

SR1500AL - Server System - 0 MB RAM

Бренд: Intel Страницы: 180

Бренд: MSI Страницы: 445

Бренд: Aaeon Страницы: 123

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды