Adler AD 1192, Руководство пользователя

Страница: 4 / 92

4
Volume control:
4. You can also press and hold the Scan – and Scan + button (7,8) for the device to automatically find the next radio signal.
3 You can change the frequency by pressing the Scan – and Scan + button (7,8).
2. The device will turn on the radio function.
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
Radio setting:
3. TO turn off the device press and hold the STANDBY / FUNCTION button (2) .
2. The device will turn on.
1. Press the STANDBY / FUNCTION button (2) once.
Turning on the device:
1. Press and hold the "SNOOZE / DIMMER" button (6) for 2 seconds to select the dimmer. Dimmer has 3 steps.
This function can be used in both “Standby Mode” and “Turned On Mode”
NOTE:
Dimmer
The alarm will start again after approx. 9 minutes.
Press the “SNOOZE / DIMMER” button (6) to suspend alarm sound for a few minutes.
Snooze
3. The display (1) will also show the alarm current setting.
2. The dot next to the AL-1 or AL-2 respectfully on the left side of the display (1) to signal the alarm is turned on.
1. To turn on the alarm press the the Vol-/Vol+ / Al.1/Al.2 Button (4,5) button once.
Alarm turning On:
7. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
6. Choose the volume level of the Buzzer or Radio playing by pressing the SCAN +/- buttons (7,8).
5. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
4. Choose alarm type between BUZZ and TUNE. Buzzer or Radio. The radio choice will turn the last used radio station.
3. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
2. Choose time by pressing the SCAN – and SCAN + button (7,8).
1. Press and hold the Vol-/Vol+ / Al.1/Al.2 Button (4,5). The display (1) will start to blink.
Alarm 1/2 setup:
3. Confirm your choice with the CLK / MEM (3) button by pressing it once.
2. Choose time format 12 / 24 H by pressing the SCAN +/- buttons (7,8).
1. Press and hold the Clk. / MEM. Button (3). The display (1) will start to blink.
Clock setup:
5. Insert the device AC power cord (13) into the wall socket (220-240 V 50/60Hz.)
4. Close the backup battery door (14).
3. Insert 2 AAA 1.5V batteries in the position shown inside.
2. Open the backup battery door (14).
1. Remove all the packing material from the device.
Setting up the device:
Before powering the device on. Remove all packing material and read the instruction manual carefully. Keep it for future reference.
15. AUX-IN JACK 16. USB CHARGING PORT
13. AC POWER CORD 14. BACKUP BATTERY DOOR
11. WIRELESS CHARGE LOCATION 12. ANTENNA
9. SLEEP / PRESET button 10. PLAY / PAUSE button
7. SCAN- button 8. SCAN+ button
5. / ALARM 2 button 6. SNOOZE / DIMMER button
3. CLOCK / MEMORY button 4. VOLUME- / ALARM 1 button .
1. DISPLAY 2. STANDBY / FUNCTION button
Device description (Clock radio):
17 . The device should be kept in a dry room.
16 . The device may only be wiped with a dry cloth. Do not use water or cleaning fluids.
15 . Avoid getting the device wet.
device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.