ADJ REV186 Скачать руководство пользователя страница 5

ADJ Products, LLC  -  www.adj.com  - Revo 4 IR User Manual Page 5

  

Revo 4 IR            

                                                                        

Safety Precautions

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before 

You Attempt To Install Or Operate This Unit!

•  To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.

•  Do not spill water or other liquids into or on to your unit.

•  Do not attempt to operate this unit if the power cord has been frayed or broken.

•  Do not attempt to remove or break off the ground prong from the electrical cord. This prong is 

    used to reduce the risk of electrical shock and fire in case of an internal short.

•  Disconnect from main power before making any type of connection.

•  Do not remove the cover under any conditions. There are no user serviceable parts inside.

•  Never operate this unit when it’s cover is removed.

•  Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” 

    (15cm) between this device and a wall.

•  Do not attempt to operate this unit, if it becomes damaged.

•  This unit is intended for indoor use only, use of this product outdoors voids all warranties.

•  Always mount this unit in safe and stable matter.

•  Power-supply cords should be routed so that they are not likely to be walked on or pinched by 

    items placed upon or against them, paying particular attention to cords at plugs, convenience 

    receptacles, and the point where they exit from the appliance.

•  Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 17 

    for cleaning details.

•  Heat -This fixture should be situated away from heat sources such as radiators, heat registers, 

    stoves, or other appliances (including amplifiers) that produce heat.

•  The fixture should be serviced by qualified service personnel when:

  A.  Objects have fallen, or liquid has been spilled into the appliance.

  B.  The appliance has been exposed to rain or water.

  C.  The appliance does not appear to operate normally or exhibits a marked change in 

   performance.

Содержание REV186



















Отзывы: