ADJ Products, LLC - www.adj.com - Flat Par TRI7XS User Manual Page 11
Flat Par TRI7XS ADJ LED RC Operation
The
ADJ LED RC
infrared remote
(sold seperately) has many differnet
functions and gives you complete control of your Flat Par TRI7XS.
To control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away. To use the ADJ
LED RC you must first activate the fixtures infrared receiver, to acti-
vate the receiver please see the instructions on page 10.
BLACKOUT
-
Pressing this button will blackout the fixture.
AUTO RUN
-
This button will run an automatic program. You can
control the speed of the Auto Run by pressing the SPEED button first
and then pressing the “+” and “-” buttons.
PROGRAM SELECTION
-
This button will let you access the units
built-in programs. Pressing this button and then press the “+” or “-”
to navigate through the built-in programs.
FLASH
-
This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED
-
Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
DMX MODE -
This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 13-17 for DMX modes, values, and traits.
SOUND ACTIVE -
This button activates sound active mode.
SLAVE -
This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS -
Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
R G B -
Press either one of these buttons and the press the “+” or “-”
to adjust the brightness.
“+” and “-” -
Use these buttons to adjust the flash rate, speed of the
Auto Run, sound sensitivity, and program selection.
ADJ Products, LLC - www.adj.com - Flat Par TRI7XS User Manual Page 10
Flat Par TRI7XS Operating Instructions
will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE
button to exit.
Infrared Receiver:
This function is used to activate and deactivate the infrared receiver.
When this function is activated you can control the fixture using the
ADJ LED RC (Remote Control). Please see the next page for ADJ LED
RC controls and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents
either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave set up. In a Master-Slave set up one unit will act as the control-
ling unit and the others will react to the controlling units built-in pro-
grams. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Connect the first “Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation. The
“Slave” unit will now follow the “Master”.
Flat Par TRI7XS Master-Slave Set Up
