ADInstruments PowerLab 2/20 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 54

background image

Chapter 1 — Overview

5

this chapter discusses the different features, connectors, and
indicators of the PowerLab 2/20 and PowerLab 4/20.

The Front Panel

The front panel of your PowerLab provides most of the connectors for
interfacing with external signals, and indicators for various functions.
This section describes each of the front panel features.

The PowerLab 2/20 has three indicators at the left of the front panel,
one BNC connector for the external trigger, two BNC connectors for
output, and two BNC connectors (marked Input 1 and Input 2) with
two alternative pod (DIN) connectors, for recording external signals.

The PowerLab 4/20 has three indicators at the left of the front panel,
one BNC connector for the external trigger, two BNC connectors for
output, and four BNC connectors (marked Input 1 to Input 4) with
two alternative pod (DIN) connectors for Input 1 and Input 2, for
recording external signals.

2 20

Input 1

Input 2

Power

Status

ADInstruments

Trigger

PowerLab

Output

Trigger

Analog output connectors

Analog input connectors

Indicators

4 20

Power

Status

ADInstruments

Trigger

PowerLab

Output

Input 1

Input 2

Input 3

Input 4

Trigger

Analog output connectors

Analog input connectors

Indicators

Figure 1–1

The front panel of the
PowerLab 2/20.

Figure 1–2

The front panel of the
PowerLab 4/20.

«
...
11
12
13
14
15
...
»

Содержание PowerLab 2/20























































Отзывы:

Нет отзывов

Похожие инструкции для PowerLab 2/20

Бренд: APAR Страницы: 10

Бренд: ABB Страницы: 88

Super-writemaster SH-S183L

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 2

Бренд: Magnavox Страницы: 128

Бренд: Tascam Страницы: 76

Бренд: Panasonic Страницы: 84

Бренд: Panasonic Страницы: 133

PROLINE DMR-T3030

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 156

Бренд: Panasonic Страницы: 4

Бренд: Line Seiki Страницы: 1

Бренд: Sony Страницы: 10

Бренд: dallmeier Страницы: 52

Бренд: Panasonic Страницы: 120

Stereo-Compact 88

Бренд: Viking Страницы: 15

Бренд: Hyun Won Страницы: 18

Бренд: GGKaiser Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды