Safety Precautions
The following are basic precautions to ensure user safety
and reduce the risk of property damage.
1
2
3
4
Place the drive on a level
surface.
•
Do not place the drive in
direct sunlight.
•
Avoid low- or high-temperature
environments.
•
Avoid high-humidity environments.
Handle with caution to prevent
damage from external shock.
Do not drop the drive, and
protect it fromsevere shocks.
•
It can damage the drive or cause
it to malfunction.
Do not move the drive while in operation and
do not attempt to open the disc tray byforce.
Make sure to close all working programs before
attempting to open the tray and always use the
open/close button.
Do not use cracked, distorted or
damaged discs.
Do not insert a pin into the emergency
opening while in operation.
In particular, a disc with a crack on the
inner tracks may break while in use.
•
Never allow food particles or
foreign substances to enter the
drive casing.
•
To protect against the risk of
fire, do ot spill such liquids as
alcohol and benzene on the
drive.
Do not disassemble, attempt to repair
or modify the device without express
approval as directed in the manual.
•
To reduce the risk of damage,
electric shock, and fire.
Important to read and understand
at all times
Do not disassemble
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that
you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it
will eventually result in irreparable damage to the disc.
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).
• Any change or modification not expressly approved by designated qualified personnel could
void your authority to operate this device.
Warning/Caution
Warning:
To warn the user that failure to comply with the instructions may result in
serious injury or death.
Caution:
To caution the user that failure to comply with the instructions may result in
damage to property.
5
•
Failure to do so may cause the
device to fall onto a hard surface,
resulting in damage or malfunction.
When using one EIDE cable
•
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear
of the DVD Writer.
When using two EIDE cable
•
Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear
of the DVD Writer.
- If there is only one Optical drive: select MA (Master).
Hard Drive
Slave Drive (Choose the SL Jumper)
MainBoard
Hard Drive
Master Drive (Choose the MA Jumper)
MainBoard
SEC 1
PRI 1
SEC 1
PRI 1
-If there is two Optical drive, select MA (Master) / SL (Slave).
Hard Drive
Master Drive (Choose the MA Jumper)
Slave Drive (Choose the SL Jumper)
MainBoard
(Choose the MA Jumper) (Choose the SL Jumper)
Emergency eject hole
LED
Disc compartment
Eject Button
Disc compartment
If the compartment does not open
when you press the Eject button,
power off the computer, insert a pin
or unfolded paper clip in the hole
and push firmlhy)
Front
Rear
Sound output terminal
Interface terminal
Digital output
terminal
Master/slave select terminal
Power terminal
Accessories
User Guide, Screw 4ea
Introduction
•
Design and specifications are subject to change without prior notice.
Connecting the Cables to the
DVD Writer
Connecting the Cables
Connecting the power cable
• The 4-pin power cable from the internal power unit of your computer must
be connected to the power terminal the rear of the DVD Writer.
1
Connecting the EIDE cable from a sound card
• Connect the 4-pin audio cable between the sound output terminal on the
DVD Writer and the audio input terminal on the sound card.
4
Installing a jumper on the master/slave select terminal
• Connect a jumper to the rear side of the DVD Writer.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using the
host interface signal CSEL. (In general, connection to MA is recommended.)
2
Connecting the EIDE cable
• Insert the EIDE cable, which is connected to the hard
disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)
3
Power cable
EIDE cable
Master/slave select terminal
Audio cable
CS : Cable Select(CSEL)
SL : Slave
MA: Master
6
7
Installing the Drive
Installing the DVD Writer
If necessary, attach a horizontal bracket
to both sides of the drive.
• You can purchase these accessories separately
from your computer dealer.
(Screws for use: M3 X 6 X 4)
1
Remove the plate from a free expansion slot and install the
DVD Writer, as shown in the illustration.
• If you have no free expansion slot, install the drive in place of the
diskette drive.
• Make sure to use the standardized screws supplied (M3X6).
- To use screws other than M3X6 may result in malfunction.
Intel Pentium 800MHz(or higher), 256 MB of RAM (or higher)with an EIDE
interface,Windows 2000/ XP/ Vista
2
How to install the DVD Writer on your PC. First, remove the cover;
connect the cable to the DVD Writer and then to the PC.
DVD
Writer
Horizontal
Bracket
Plate
Using the Drive/Storing and Cleaning
Your Discs
Push the power button and boot the computer.
1
After booting the computer, open the disc
compartment by pressing the Eject button.
2
Insert the disc (CD) with the label on the disc
facing upwards and close the disc compartment
by pressing the Eject button. The indicator light
comes on.
3
Play the disc (CD).
4
Using the DVD Writer
•
Do not place a disc in direct sunlight.
•
Store a disc vertically in a well-ventilated and
stable location.
•
Do not write or attach a label on a disc.
•
Do not drop a disc or place heavy objects on it.
•
Do not touch the surface
of a disc; hold it by the
edges.
•
To clean a disc, polish lightly
from the inside of the disc to the
outside with a soft cotton cloth.
Storing Your Discs
Cleaning Your Discs
•
Run the CD player program supplied with the sound card or play the
Windows Media Player.
Playing CD-DA/Audio CDs
•
Follow the instructions provided with the disc.
• A video card or MPEG software and a sound card need to be installed to view video CDs.
Playing Video CDs
•
The disc may not function properly if there are fingerprints, foreign substances or
dust on the disc surface.
•
If the drive is vertically installed, you cannot use an 8 cm Mini Disc
because the disc is movable.
8
9
Solving Technical Problems
The DVD Writer is not
detected by the computer.
After installing the DVD Writer,
the PC gets slower.
•
Check that the power, audio and EIDE cables are correctly
connected to the computer.
•
Change the EIDE cable and reconnect it to the computer.
Preferably, connect a second EIDE cable to the DVD Writer
in master mode.
•
Check the position of the jumper in the master/slave select
terminal.
The DVD Writer is not
recognized by MS-DOS.
•
Reinstall the device driver or update it with the latest version
by downloading it from the Samsung Web site.
- http:// www.samsung-ODD.com
- http:// www.samsung.com
When the MPEG software
plays a Video CD, the pictures
are not regular and the running
speed is too slow.
•
Adjust the size of the replay screen.
•
After checking the display resolution, adjust it, if necessary.
A CD is not read or is read
too slowly.
•
Check whether the CD is of good quality and clean it,
if necessary.
The disc compartment will
not open.
•
Check that the power cable is correctly connected.
•
Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
The DVD Writer is not
detected after it is connected
to a sound card.
•
The interface mode of the sound card is AT-BUS.
You must therefore connect the DVD Writer to the EIDE
port on the PC mother board, rather than to the sound card,
or install an EIDE compatible sound card.
The Disc is not in message is
displayed even though a disc
has been inserted.
•
The computer may not recognize the disc if you start playback
too quickly after inserting the disc.
Open and close the disc compartment and try again.
•
Clean the disc and try again.
•
The friction noise generated during SPIN-UP and STOP is caused by the
Automatic Ball Balancing System(ABS) and is not a malfunction.
System Requirements
Super- DVD Writer
SH-S202J(TS-H652J)
User Guide - ENGLISH
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This marking shown on the product or its literature,indicates that it should not be disposed with
other household wastes at the end of its working life.To prevent possible harm to the
environment or human health from uncontrolled waste disposal,please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,or their
local government office,for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract.This product should not be mixed with other commercial wastes for disposal.
CAUTION
Change or modifications not expressly approved by the manufacturer responsible for
compliance could void the user ’s authority to operate the equipment.
LASER STANDARD
IEC 60825-1 :1993 +A1 :1997 +A2 :2001
WEEE
Correct Disposal of This Product (Waste Electrical &Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
- http://www.samsung-ODD.com
- http://www.samsung.com
BG68-01447A REV.00
Technical Specifications
S
SH
H--S
S2
20
02
2J
J((T
TS
S--H
H6
65
52
2J
J))
DVD Writer
Category
DISC
Usable Discs
Disc Diameter
DVD : DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM, DVD-Video,
DVD+R (Dual), DVD-R (Dual), DVD-RAM, DVD Multi-Border
CD : CD-ROM, CD-R, CD-RW, CD-DA, CD+E(G)
CD-MIDI, CD-TEXT, CD-ROM XA, Mixed Mode CD CD-I,
CD-I Bridge (Photo-CD, Video-CD),
Multisession CD (Photo-CD, CD-EXTRA, Portforio),
4.72 Inch or 3.15 Inch (120mm or 80mm)
ATA/ATAPI (E-IDE)
DMA mode
CD-ROM
CD-ROM
DVD-ROM
PIO Mode 4: 16.6MB/sec
Ultra DMA Mode 4: 66MB/sec
110ms (Random)
130ms (Random)
Data transfer
rate(MAX)
Access time
(Random)
Buffer Memory
Size (Width x Height x Length)
Weight
Drive Installation
Temperature
Humidity
Operating
Environment
Interface Port
Interface
Support
PIO mode
Media Type
DVD+R
DVD+RW
DVD+R DUAL
DVD-R DUAL
DVD-R
DVD-RW
DVD-RAM
DVD-ROM(Single)
DVD-ROM(Dual)
CD-ROM
CD-R
US-RW
HS-RW
CD-RW
CAV 20X CAV 16X
ZCLV 8X CAV 12X
ZCLV 16X CAV 12X
ZCLV 12X CAV 12X
CAV 20X CAV 16X
CLV 6X CAV 12X
PCAV 12X PCAV 12X
CAV 16X
CAV 12X
CAV 48X
PCAV 48X CAV 40X
ZCLV32X CAV 40X
CLV 10X CAV 40X
CLV 4X CAV 40X
Write
Read
2MB
Horizontal / Vertical
41°F ~ 122°F (5°C ~ 45°C)
5% ~ 80% (RH)
5.83 X 1.65 X 6.69 Inch (148.2 X 42 X 170mm)
750g
•
Samsung Eco-mark
The Samsung’s own Eco mark helps consumers to easily understand that
Samsung develops eco-friendly products. This mark represents Samsung’s
continuous effort to develop eco-friendly products.
• RoHS
(Restriction of the use of certain hazardous substances in electrical and electronic equipment)
The RoHS, the environment regulation announced by European Union, restricts the use of
lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the
market in The European Union after July 1, 2006.
•
If the power cable is not connected
properly, it may cause a fire or
damage the drive. Check the direction
of the power connector and the drive
incline before connection.
+5V DC
Ground
Ground
+12V DC
When you install the drive
While operating
Other
* The product specifications above may be changed improve
device performance without prior notice.
The type of accessories varies depending on a product model.
and some accessories described herein are subject to change without notice.
* "40 Pin E-IDE cable and System requirements are available for 20X
writing. But for Optimal 20X writing, 80pin E-IDE cable and Pentium IV
2.0GHz or faster are recommended."
SH-S202J(TS-H652J)-ENG/RUS 2007.6.26 12:1 PM Page 1
