ADIATEK ruby 45c, Использование и обслуживание, Страница: 8 / 14

GB GB
8
In order not to cause permanent damages to the
batteries, it is necessary to avoid their complete dis-
charge, providing for the recharging within a few
minutes after batteries discharge signal starts blink-
ing.
NOTE: Never leave batteries completely discharged
even if the machine is not used. In case of traditional
batteries, please check the electrolyte level every 20
recharging cycles and eventually fill them up with
distilled water.
ATTENTION:
For the daily recharge of the batteries it is necessary
to follow strictly all the indications given by the
manufacturer/distributor. All the installation and
maintenance operations must be carried out by
qualified staff.
Danger of gas exhalations and
emission of corrosive liquids. Fire danger: do not
approach with free flames.
BATTERIES DISPOSAL
It is compulsory to hand over exhaust batteries, clas-
sified as dangerous waste, to an authorized institu-
tion according to the current laws.
BATTERIES CHARGE LEVEL INDICATOR
WHEN THE MACHINE IS SWITCHED ON, ON THE DIS-
PLAY (1) APPEARS THE SETTING OF THE BATTERY
CHECK CARD:
GE 24: check card set for GEL batteries.
Pb 24: check card set for lead batteries.
On the display (1) the following indication of the
battery charge level is digital and indicates the per-
centage of the battery charge. 100 is the maximum
charge, down to a minimum of 10, indicating every
10% decrease.
When the charge level reaches 10%, the display
starts blinking indicating the end of the battery
charge.
ATTENTION:
After a few seconds from the four blinking ‘’----’’
dashes, the brushes motor stops automatically. With
the remaining charge it is anyhow possible to finish
the drying operation before proceeding to the re-
charge.
HOUR METER
The machine is equipped with an hour meter located
on the same display of the battery charge level indi-
cator (1). Keeping the button (2) pressed for more
than 3 seconds, the first data indicates the working
hours and after a few seconds the working minutes
are shown.
SQUEEGEE ASSEMBLY
With the squeegee support lowered, slide the two
stud bolts (1) placed on the upper part of the squee-
gee inside the slots on the support. Block the squee-
gee by rotating the lever (2) clockwise.
Insert the squeegee hose (3) into its coupling, re-
specting its position as indicated in the figure.
ADJUSTMENT OF THE SQUEEGEE HEIGHT
The squeegee must be adjusted in height depending
on the rubber wear. In order to guarantee a perfect
drying during the operation, the lower blade of the
rear squeegee rubber (4) must work slightly bent
backwards (operator side) in uniformed way in all its
length.
Acting clockwise upon the two registers (5) it is pos-
sible to increase the bending of the rubber. Acting
counterclockwise it is possible to decrease the rubber
bending.
A label placed near the two registers (5) indicates ro-
tation sense to increase or reduce the height.
Note: The wheels of the squeegee support must be
adjusted through the registers (5) at the same height
so that the squeegee works parallel to the floor.
ADJUSTMENT OF THE SQUEEGEE INCLINATION
In case of need, to increase the rubber bending in
the central part, it is necessary to tilt the squeegee
rotating counterclockwise the register (6). To in-
crease the rubber bending on the squeegee extremi-
ties, rotate the register clockwise.
BRUSHES ASSEMBLY
1. Take off the electric supply to the brushes motor
unplugging the batteries connector (1). For machines
equipped with key switch (see under "OPTIONAL AC-
CESSORIES"), turn the key counterclockwise.
2. Acting upon the pedal (10) lift the brushes base
group.
3. With the brushes base group in lifted position,
unscrew the two wing nuts (1) and then remove the
side support of the brushes (2).
4. Insert the brushes (3) into their seats from the
side of the hexagonal coupling, taking care to find
the coupling at the opposite end and to insert them
completely.
5. Reposition the side support (2) so that the sup-
port pins enter into the bearing holes visible at the
centre of the brushes frame.
6. Retighten and block the wing nuts.