background image

 

Battery Charging 

 

CAUTION: 

 

Make sure that the AC voltage of the power source meets the requirement specified on the 
nameplate of the charger. 

Plug the battery charger 

FFCL18-01

into the proper AC power source. The charging indicator 

light will flicker in green color and the charger operates in standby mode.   

 

Charging Operation 

1.

 

Plug the battery charger into the proper AC 
power source. The charging indicator light 
will flicker in green color and the charger 
operates in standby mode. 

 

2.

 

Insert the battery pack fully into the battery charger and the charger starts charging.   

The battery charger can detect some sort of failure caused by the battery and indicates by the 
statuses of the red and green indicator lights. 

When a failure occurs, remove the battery and then insert it into the charger again. If the failure 
continues, change with a new battery. If the new battery can be charged, then the old battery 
maybe damaged. If the charging indicator lights indicate same failure as before while changing 
with a new battery, then the charger maybe damaged, take the charger to be repaired by qualified 
serviceman. (Fig. 11) 

The following chart lists the relations between the statuses of charging and charging indicator 
lights. 

 

Work Light 

The white LED work light will be lit when pull the 
switch trigger, allows for illumination of the work 
area under unfavorable lighting conditions. (Fig. 
12) 

 

Continuous Use 

If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest 
for 15minutes before proceeding with a fresh battery. 

Status of RED LED Lights 

Approx. Battery Power Left 

4 lights lit 

≥3/4 

3 lights lit 

≥1/2 

2 lights lit 

≥1/4 

1 light lit 

1/4 

1 light extinguished after 5 times flash 

Low level 

Battery Charger Model 

FFCL18-01 
FFCL18-03 

SCHARG-001 
(FFCL18-04) 

Charging Voltage 

220-240V 

110V-240V 

Charging Current 

3.0A 

Charging Frequency 

50-60Hz 

Applicable Battery Pack Voltage 
(DC) 

14.4-18V 

Applicable Battery Cartridge 
Capacity 

4.0Ah 

5.0Ah 

Full Charging Time (Approx.) 

90mins 

100mins 

Insulation Class 

Double Insulation 

Charge State 

Icon 

Light Icon 

Indicator State 

Green 

Red 

Charger Into The Power Sour  

 

 

 

Green Flick, Red off 

Charging 

 

 

 

Green off, Red on 

After Charging 

 

 

 

Green on, Red off 

Battery Abnormal 

 

 

 

Green Red Flick 

Battery Temperature Below 
0

or Over 45

 

 

 

 

Green off, Red Flick 

                           

-15-                                                                              

 

Содержание MAC AFRIC SWRENC-001











Отзывы: