ADEEPT Smart Car Kit Скачать руководство пользователя | Manualshive

Страница: 38 / 58

background image

www.adeept.com

34

Arduino Nano Board

Adeept UNO R3 Board

How Should I Use Arduino?

If you are a beginner with Arduino, Arduino learning kits on our website

would

be a prefect step into this fantastic field!
Two types of Arduino board are used in this car kit: Adeept UNO R3 Board and Arduino Nano
Board.

Power

The Arduino/Genuino Uno board can be powered via the USB connection or with an external
power supply. The power source is selected automatically.
External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The
adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack.
Leads from a battery can be inserted in the GND and Vin pin headers of the POWER connector.
The board can operate on an external supply from 6 to 20 volts. If supplied with less than 7V,
however, the 5V pin may supply less than five volts and the board may become unstable. If using
more than 12V, the voltage regulator may overheat and damage the board. The recommended
range is 7 to 12 volts.

The power pins are as follows:

Vin. The input voltage to the Arduino/Genuino board when it's using an external power source
(as opposed to 5 volts from the USB connection or other regulated power source). You can supply
voltage through this pin, or, if supplying voltage via the power jack, access it through this pin.
5V. This pin outputs a regulated 5V from the regulator on the board. The board can be supplied
with power either from the DC power jack (7 - 12V), the USB connector (5V), or the VIN pin of the
board (7-12V). Supplying voltage via the 5V or 3.3V pins bypasses the regulator, and can damage
your board. We don't advise it.
3V3. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.
GND. Ground pins.
IOREF. This pin on the Arduino/Genuino board provides the voltage reference with which the

«
...
36
37
38
39
40
...
»

Содержание Smart Car Kit



























































Отзывы:

Нет отзывов

Похожие инструкции для Smart Car Kit

Бренд: WEISS ROBOTICS Страницы: 69

Recon Scout OCU02

Бренд: ReconRobotics Страницы: 12

KidzRobotix BUBBLE ROBOT

Бренд: 4M Страницы: 2

Бренд: Lynxmotion Страницы: 3

4-DoF SCARA Style Arm Kit

Бренд: HEBI Robotics Страницы: 21

Бренд: YASKAWA Страницы: 92

Бренд: Epson Страницы: 314

Бренд: Epson Страницы: 668

Бренд: Motoman Страницы: 79

Бренд: Opitec Страницы: 9

Бренд: ItaldibiPack Страницы: 43

Chameleon Tongue

Бренд: Festo Страницы: 11

Bionic Elephant Trunk

Бренд: Festo Страницы: 16

Бренд: FISNAR Страницы: 118

Table Tennis Table City Concrete Outdoor

Бренд: Butterfly Страницы: 2

Fitness Outdoor Table Tennis Table

Бренд: Butterfly Страницы: 2

Бренд: Butterfly Страницы: 4

Бренд: Butterfly Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды