Adjustment of weight unit:
Place the scale on a table. The scale will automatically switch-on and the LCD display will
indicate “8888” and a few seconds later “0.0 kg“. By pushing
or
button (located at
the front side of the
scale) it is possible to change the unit of weight for country specific
setting (kg = kilogram / st = stone / lb = pound). To confirm the entry push the SET-
button. Please pay attention to use the scale under consideration of your country specific
unit of weight.
4. Weighing function (weight measurement only)
1. Switch on the scale by using the tap-on-function. For this, tap with your foot short
and forceful on the centre of the scale. The display indicates the signal „8888“ and a
few seconds later “0.0” kg. Now the scale is ready to use.
2. Step on the centre of the scale. Remain stationary on the weighing platform and do
not hold you tight. After a few seconds, your weight will be indicated.
3. After weighing, step off the scale. A few seconds later, the scale will automatically
switch-off.
5. Programming / Enter of personal data
Before first time use your personal data like gender (female or male), body height and
age must be programmed and saved under selected locations P1 – P0 (up to 10
persons). The enter keys are located at the front of the scale. To enter your personal data
please utilise the buttons: SET (on and save button),
(plus button),
(minus button)
and follow the particular points:
1. Place the scale on a table. The scale will automatically switch-on and the LCD
display will indicate “8888” and a few seconds later “0.0 kg“. Now press the SET-
button. The display indicates flashing “P1”. To select your personal location (1 - 10),
press
or
button. After the selection of your personal location press the SET-
button to save the reading.
2. After you have selected your personal location (e.g. P2), the symbol for gender starts
to flash. To select the requested gender (male / female), press
or
button. After the
selection of your gender press the SET-button to save the reading.
3. After you have selected your gender (e.g. female), the symbol for age starts to flash
(default 25 age). To enter your age, press
or
button. After the selection for your
age press the SET-button to save the reading.
4. After you have selected your age, the symbol for body height starts to flash (default
170 cm). To enter your height, press
or
button. After the selection of your height
press the SET-button to save the reading.
After input completion, the display indicates “- - -”. Your entered personal data will be
indicated and shortly after “0.0 kg”. A few seconds later, the scale automatically powers-
off.
To enter personal data of further persons please repeat the steps listed below.
6. Body Analysis
An analysis is only possible in bare feet. Your personal data must be entered first (please
see page 4 - 5).
1. Switch on the scale by using the tap-on-function. For this, tap with your foot short
and forceful on the centre of the scale. The display indicates the signal „8888“ and a
few seconds later “0.0” kg. Now press the SET-button and select your personal
location by using
or
button.
2. At first, your personal data (age, body height, and gender) will be indicated and shortly
after the indication, “0.0 kg” will appear on the display.
3. As soon as “0.0 kg” appears in the display the scales is prepared for the
measurement.
4. Carefully step on the stainless steel strips (measurement module) of the scale in bare
feet and remain stationary while the measurement is now taking place.
4. At first, your weight will be indicated on the display. Shortly after, while the analysis
is taking place, the signals “o” starts to move. After completion of the measurement,
your measured values (weight, body fat, body water, muscle mass and bone mass) will
be shown in changes successively 3 times.
EXAMPLE:
Indication:
Weight Body Fat Body Water
Muscle Mass Bone Mass
5
4
