Megabit Modem
®
MM702G2-W V5.x
Quick Installation Guide
Page 1 of 4
O
VERVIEW
The MM702G2-W modem is a versatile, high-speed 1-pair/2-pair G.SHDSL modem that
extends an Ethernet LAN in either a back-to-back implementation or as a CPE that connects
the LAN to one or more service providers through a DSLAM. The modem uses G.SHDSL
technology in either fixed-rate or rate-adaptive mode with symmetric rates up to 4.608 Mbps.
MM702G2-W supports Bridging, Routing, IEEE 802.1q (VLAN), IEEE 802.1p (Priority
Queueing), Proxy ARP, Virtual IP Interfaces, Secondary IP Address, ZIPB, Management IP
Address Control,
NAT, F4/F5 OAM, PPPoA, PPPoE, IPoA, Security, Traffic Filtering, Firewall,
SNTP, IGMP, SNMP v1/2, Intrusion Detection, RIP v1/2, DHCP, DHCP Client/Server, DHCP
Relay,
DNS relay and other essential features.
The modem supports eight simultaneous Bridge/Router, PPPoA, PPPoE or IPoA sessions to
the same or different service providers over its G.SHDSL WAN interface. The modem offers
an easy-to-use Web-based interface.
The MM702G2-W modem includes protocols and services that enhance configuration and
performance. If you require IP addresses to be served dynamically on your LAN, use the
built-in DHCP server. If you require a name to IP address resolution, use DNS Relay. If you
need to update your modem software, use the Web HTTP Upgrade. If you require private
IP addresses and need to translate them into public IP addresses, use the built-in NAT
function. If you need to exchange IP routing information with another device, configure an
implement RIP. If you need F4/F5 OAM, it is enabled on the configured WAN sessions.
Use this guide to install your modem and access the configuration pages. To configure the
modem, refer to the
Megabit Modem MM702G2-W User Manual
on the documentation CD
(included in the modem box).
S
YSTEM
R
EQUIREMENTS
Before installation, verify these system requirements:
• PC with a 10/100Base-T Ethernet Network Interface Card (NIC)
• TCP/IP protocol stack (see the documentation for your operating system)
• Web browser installed such as Internet Explorer (Version 6.0 or higher)
V
ERIFY
S
HIPPING
P
ACKAGE
C
ONTENTS
Inspect the contents of the shipping package for the following:
• Modem unit
• 6-Vdc power supply with cord
• Ethernet cable (black, Cat 5-UTP) Phone cord (silver) with RJ-11 connectors for SHDSL
connection
• Console cable (gray) and DB-9 console port adapter
• Documentation CD
S
TEP
1: C
ONNECT
THE
C
ABLES
After verifying the shipping package contents, follow this procedure to connect the modem:
1. Set the MDI/MDI-X switch to:
• MDI-X when connecting to a network device such as a PC with an Ethernet NIC card that
has an MDI port
• MDI when connecting to a device such as a hub, switch, or router that has an MDI-X port
2. Connect the cables to the modem rear panel and to the facility or other equipment as
shown below.
• Silver phone cable for the SHDSL line port
• Black Ethernet cable for the 10/100Base-T port
• Power cable for the modem Power connector
Wall jack with
SHDSL service
SHDSL line
port
Power
connector
PC, hub or other
network device
10/100Base-T
port
M0342-A
For connection to
devices such as
a PC Ethernet NIC
For connection to
devices such as a
hub, switch, or router
MDI-X
MDI
Reset
